no bug IHADSS gunner sight is not really match from pilot seat

[Danhopark323]

IHADSS should show where gunner is looking at, but after the latest patch, on IHADSS, gunner is looking at empty space, but on TADS, gunner is aiming a right target. Everything works, but it is impossible for pilot to check where the gunner is looking

The First image showing gunner is looking at empty field, but when I check it with VID TADS, it is aiming BTR

The last image shows where the hellfire goes to the gunner's aim. Which is far away from the gunner cross-hair on IHADSS
 

LastMissionTrack.trk

Edited yesterday at 07:27 AM by Danhopark323

[LorenLuke]

56 minutes ago, Danhopark323 said:

IHADSS should show where gunner is looking at, but after the latest patch, on IHADSS, gunner is looking at empty space, but on TADS, gunner is aiming a right target. Everything works, but it is impossible for pilot to check where the gunner is looking

The First image showing gunner is looking at empty field, but when I check it with VID TADS, it is aiming BTR

The last image shows where the hellfire goes to the gunner's aim. Which is far away from the gunner cross-hair on IHADSS
 

LastMissionTrack.trk 981.69 kB · 0 downloads

User error.

I can tell immediately from the IHADSS that your acquisition source is set to a Cursor Acquisition/Terrain Point (TRN). Whenever you CAQ on the map, where you drop that point becomes the Acquisition Source (ACQ). The reason the dotted cross is pointing to an open field is because the dotted cross points out your Acquisition Source, and your Acquisition Source is a TRN point in an open field. You need to set your Acquisition Source back to TADS to see where George is pointing the TADS in your helmet (I recommend through the weapons page).

[Danhopark323]

31 minutes ago, LorenLuke said:

User error.

I can tell immediately from the IHADSS that your acquisition source is set to a Cursor Acquisition/Terrain Point (TRN). Whenever you CAQ on the map, where you drop that point becomes the Acquisition Source (ACQ). The reason the dotted cross is pointing to an open field is because the dotted cross points out your Acquisition Source, and your Acquisition Source is a TRN point in an open field. You need to set your Acquisition Source back to TADS to see where George is pointing the TADS in your helmet (I recommend through the weapons page).

This is crystal clear answer! I had same issue after switching to NVG and TADS on IHADSS, but this solved it too Thank you

[devnull]

hi folks, i discovered sth similar. i have differences in between hot and cold start using george ACQ = TADS slew to PHS.
So when i cold start my chopper, even if i have boresighted or not, The point where george slews the TADS to is some kind off.
I made two videos to show. what i am missing ? Or is this somehow a bug?
 

 

 

[Floyd1212]

31 minutes ago, devnull said:

So when i cold start my chopper, even if i have boresighted or not, The point where george slews the TADS to is some kind off.

This seems unrelated to the OP's problem with Acquisition Sources, but more to do with how you are boresighting the IHADSS.  You should do some research on that, and maybe post a video of your boresighting process in a new thread if you still need help.  (In a Hot Start, the boresight is already performed properly for you.)

[devnull]

vor 40 Minuten schrieb Floyd1212:

This seems unrelated to the OP's problem with Acquisition Sources, but more to do with how you are boresighting the IHADSS.  You should do some research on that, and maybe post a video of your boresighting process in a new thread if you still need help.  (In a Hot Start, the boresight is already performed properly for you.)

i agree, it must be sth. different.

hers my BSight procedure, i tried in VR and 2D. Both times reproducable,but  rly depends on BS. i made the negative test, BS somewhere way off, and the slew was extremely off.
but can´t do anything then exactely look into that tube!

 

Edited 20 hours ago by devnull

[Floyd1212]

You're not aligning the rings to be concentric inside the BRU tube.

You want them centered in the tube, and your crosshairs centered on the rings.

[devnull]

ok, ill take care of it and test.Thanyk you very much

Update:

vr PROCEDURE; how exact needs this to be?!

 

 

 

Edited 20 hours ago by devnull

[admiki]

More precise you are, more precise slew will be.

[devnull]

figured it out, i have IHADS rendered on both eyes!! if i want to leave it like that, i have to close for example the left eye and aim like this.
 

 

Edited 15 hours ago by devnull

[LorenLuke]

5 hours ago, devnull said:

figured it out, i have IHADS rendered on both eyes!! if i want to leave it like that, i have to close for example the left eye and aim like this.
 

 

I believe the monocle is calibrated to the right eye, so you need to boresight with the right eye for it to work.

[Zarma]

Yea IRL the monocle is on the right eye. I use it that way in VR, just take a little time to get used to, especially the PNVS.

I don't know how they do the boresighting with both eyes, but could be the problem.