Dual Rudder Axis - How?

[ivanwfr]

CONTROLS

- Rudder

- - Logitech G27 Racing Wheel

- - - JOY_Y;JOY_SLIDER2

- - - - AXIS TUNE

 

Axis Tune: JOY_Y (right pedal)

- - - - - Deadzone = 0

- - - - - Saturation X = 90

- - - - - Saturation Y = 50

- - - - - Curvature = -50

- - - - - SLIDER = [Checked]

- - - - - Invert = [Checked]

... red dot (pedal pushed then released once) full left rest position, near top of curve, goes down+right when pushed and moves black square from its full right start position to the left up to the center and has very little effect from mid-to-full pedal excursion.

 

Axis Tune: JOY_SLIDER2 (left pedal)

- - - - - Deadzone = 0

- - - - - Saturation X = 90

- - - - - Saturation Y = 50

- - - - - Curvature = -50

- - - - - SLIDER = [Checked]

- - - - - Invert = [unchecked]

... red dot (pedal pushed then released once) full right rest position, at origin of curve, goes left+down when pushed and starts moving the black square from its middle rest position to the left when it reaches 1/3 excursion.

 

But JOY_Y graphics are all wrong as the "Invert=checked" option is not correctly applied here... and works perfectly in-game!

( I did file a ticket about that but who cares :( )

 

In fact, , with Invert=unchecked to compensate, aside from a "center-point-symetry" representation, JOY_Y (right pedal), display shows that we can move the black square :

- from full-right to center with JOY_Y (right pedal)

- from center to left with JOY_SLIDER2

... center being the rightful Rudder rest position

 

Just go on experimenting with all this and you could get something working from all this mess in-game with "RCtrl+Enter" (Show controls indicator)

[TRITATUTTO]

Hi guys , i have a Logiteck attack 3 and a g25 racing wheel.

When i go in the option menu , the sim see the first and the second one , but not the pedals , i mind it see all the buttons , on the wheel , on the gear sistem , but when i press the pedals for the rudder , nothing it dont recognize them ...

I have dcs world 1.2.0 ( with patch BS2)and BS 2 standalone.

What is the problem , i try everything , but i dont know why the sim dont see the pedals , Thank you !

Edited August 18, 2012 by TRITATUTTO

[TRITATUTTO]

Tonight i try again and it works ! But i have a question.which is the difference beetwen rudders control in the axes option and select left rudder and right rudder separately in "all" section ?

Some time when i leave the foot on the pedals seem to not recenter properly , any tips for that ? Thank you !

[cichlidfan]

Tonight i try again and it works ! But i have a question.which is the difference beetwen rudders control in the axes option and select left rudder and right rudder separately in "all" section ?

 

The rudder options in the 'all' category are keyboard commands and are not compatible with an axis. There are similar commands for pitch and roll control via keyboard as well.

[PeterP]

Tonight i try again and it works ! But i have a question.which is the difference beetwen rudders control in the axes option and select left rudder and right rudder separately in "all" section ?

Some time when i leave the foot on the pedals seem to not recenter properly , any tips for that ? Thank you !

 

A key press for the rudder is a absolute value - means:

turn rudder to max left/right position until I release the key.

 

 

A axis is a relative value - means:

check where I hold the axis and bring the rudder to this point.

Edited August 18, 2012 by PeterP

[ebabil]

hi guys. i got a cheap driving wheel. pc sees pedals as pich up and pich down axis. how can i set them as rudder?

[Dachs]

Reviving an old thread here, as I found no solution, when searching for G25 with Leo Bodnar cable, as rudder pedals. Just posting in the hope this will pop up should others be searching for the same..

 

Anyway, I managed to get mine working as rudders directly in the sim, by inverting the axis of both clutch and gas pedal, using Bodnars calibration program.

 

Download link here http://www.leobodnar.com/products/DFPG25conn/Calibration-DFP-G25.exe