vctpil

Hi, I have used with success to fire rockets in reference with the table setting found in the Quickstart manual page 27. But I absolutely not able to place a bomb on the target. They are falling well, well before the target. I have watched a lot of tutorial on youtube, but I have found them totally unrealistic, dropping bomb at a very low altitude without using any references or even not setting the gunsight reflector. Have you got this problem ? What is your technique for bombing ? Thanks, Vincent

- Easy radio disabled, - On parking position with hot engine, - 125.00, 39.20 and 254.00 does not work - No ATC text or audio - Tried with the L-39 and the A-10C I also agree that it is an alpha version, and there will be a lot of bugs to be fixed. At least, I am not alone and I hope it will help. Cheers, Vincent

Hi, It seems there is no way to communicate with the tower on Nellis with the L-39C. I preselect 125.00Mhz and 254.00Mhz on the mission editor and try from the forward and rear cockpit, but I have no answer. Anybody have the same issue ? Thanks, Vincent Edit : I have the same problem with the A-10C on all the frequencies (125.00, 39.20 and 254.00).

Hi, I tried something different this morning. I made a fresh installaton of DCS 1.5. I start the launcher WITHOUT updating it, and... it works! So I left the soft and start again to update in 1.5.1.47285.107, and it works. After that, I uninstall everything, clean everything, and install again with the update, without launching the soft before the update. Then, the error 0xc00007b appears! Strange, isn't it? By the Way, I tried dependency walker, but foe each software (P3D, Falcon BMS, X-Plane and DCS), I have some red x64 and some black x86. Is it normal ? Thanks.

Hi, I tried something different this morning. I made a fresh installaton of DCS 1.5. I start the launcher WITHOUT updating it, and... it works! So I left the soft and start again to update in 1.5.1.47285.107, and it works. After that, I uninstall everything, clean everything, and install again with the update, without launching the soft before the update. Then, the error 0xc00007b appears! strange, isn't it?

Hi, As the DCS 2.0 is about to be available, what will happen if the f**** error 0xc00007b happen again ? I bought the L-39 and pre-order NTTR Nevada, what if can't use it ? Thanks.

Yes, I have not updated my signature yet. On this old config, I had the same problem solve by repairing C++2010. And by the way, DCS 1.5 and the L-39 was working perfectly, very fluid.

Tried also, doesn't work. I installed C++ 2008, 2010, 2013, 2015, removed, re-install, repair, without result. It is a very bad things, I cannot fly with the L-39 anymore !

Hi, I also try re-installing DX11, but I still have he same error message Until now, Prepar3D v3, X-Plane and Falcon BMS 4.33 are working really don't understand why DCS 1.5 is not working. Thanks for any ideas. Vincent

Hi, After un big upgrade of my computer and a fresh install of W7 64bit, I have this message again : The program couldn't start properly (0xc000007b). Click OK to close the program How is it possible ? I have covered some threat on this forum and have tries all solutions (Re-install and repair DX, VC++ Runtime, etc) but none are working ! Anyone has a definitive solution about this problem ? Thanks Vincent

Thank a lot, I found it.

Slovak Air force Hi, How do you select the Slovak air force livery ? This country does not appear in the list on the mission editor. Thanks, Vincent

Hi, I have read the DCS manual and the real L-39 manual about the gunsight, but I really don't understand some points, like the fictitous target base. Is there a detailed manual explaining how the gunsight is working ? Thanks, Vincent

I didn't know this serie, thanks. Any chance to have it in HD ? Vincent

Hi, The problem of people don't flying real aircraft is how they cannot set the flight control setting correctly in the sim. I have never flew the L-39, but I have +4000h on propeller and jet liner. I set the Y,X and Z axis as follow : Deadzone : 5 Both saturation : 100 Curvature : 40 I cannot judge the flight model of the L-39, but I am pretty satisfied with those preleminary settings. Read also the real flight manual available on this forum. The nose was bouncing slightly during an approach at 200 km/h until I discovered that the speed should be around 230 km/h. The aircraft is more stable like that. Also, try to roll at the maximum at slow and high speed. You will notice a difference in flight path stability. This aircraft has maybe not the best flight model, but as far as I know, it seems to be close to the real one. Cheers, Vincent

I hope it they will fix it, the A-10C has the same problem with the "boat" switch.

Hi, I noticed that the trim must be full up (Index 2 on the trim panel) for the take-off, and I even had to trim a little bit more up for the climb. Situation is from take-off in instant action. That sounds to be a bug, but anyone has the same problem ? Thanks, Vincent

I had this one also after the install. Just search with google "MSVCR120.dll" and install it on system32. By the way, despite my computer performances, a free flight with the L-39 is perfectly fluid. Cheers

Hi, I tried this one, and it works, at least for me : https://msdn.microsoft.com/en-us/library/aa983433(v=vs.90).aspx I hope that can help. Cheers, Vincent

I am agree my video card is not the best one today, and I am supposed to change computer in a couple of week. But this actual video card support DX11. The minimum required does not specify the video card. OS 64-bit Windows 7/8/10; DirectX11; CPU: Core i3; RAM: 8 GB; Free hard disk space: 30 GB; Video: 2 GB RAM card, DirectX11 - compatible; requires internet activation. At least, the soft should start, but not with the best performances. Vincent

Hi, The installer works correctly and inform me that the filas has been updated sucessfully. But, it does not start and show this message : The application does not start correctly (0xc000007b) Click OK to close the application notice that I have never had any problem with any product from DCS. Any help appreciated. Thanks, Vincent

Hi, This is not the first bug with the ILS button : http://forums.eagle.ru/showthread.php?t=129940&highlight=ILS I hoped it would be solved in the next update, but... Cheers, Vincent

Hi, Does the fire at point works with the latest version 1.2.7.xxx ? I tried, but nothing happen; Thank for your report. Vincent

Hi, I uninstall TARGET and I clean the registry. The switches are still not working correctly. And I don't know how TARGET could be the source of the problem. Thanks anyway.

Hi, Thank for the answer. No, for example, the exterior lights does not comme off when the pinky switch is centered. It seems that the simulator does not recognize the center position. Cheers, Vincent