Futurecvsh

Okay, I'll upload the information the next time I enter the game! One more piece of information that I wanted to add is the following, the missions that I upload created by me in the mission editor are in a separate directory-folder outside the game C:\MISSIONS I don't have them on the common route C:\Users\{username}\Saved Games\DCS\Missions Could that be the problem?

When I start a mission from the airport, on the ground, with various objects placed by me at the airport in the mission editor (planes, helicopters, vehicles) I have a drop of about 5-10 FPS, this lasts approximately 30 or 40 seconds Afterwards, my FPS stabilized again at the 60 that I have established, I have tried multiple things, deactivate accelerated Windows GPU, deactivate Windows game mode, repair DCS installation, activate VSYNC or FASTSYNC, deactivate core 0, deactivate HOTPLUG, set high priority, delete "FXO" and "METASHADERS 2" folders, reinstall Nvidia driver, ETC.. I get this FPS drop only in some modules, Chinook, F4, Apache, before From the December 24 update this did not happen, and as I said it is only from the ground with several objects-vehicles on it. ground, and it is only temporary because after several seconds my FPS stabilizes again, my computer is quite decent, i7 12700k, RTX 4090, 64GB DDR4 RAM, I have also disabled any overclock, and my CPU temperatures are good (70 degrees ) and GPU (65 degrees) approx, also my GPU and CPU workloads are normal, below 60% on GPU, and 40-50% on CPU (yes, I have observed that the first core has a very high load at the beginning, 80-90%, but I also tried to deactivate it and the same thing happens) Does anyone know what it could be or does this happen to anyone else? I need help, thanks

Same here

Same here

I also have problems with a high-performance computer and a few months ago I didn't have them, I have seen the big problem, it overloads a processor core a lot, but it only happens to me at the beginning of a mission if there are many objects placed through the editor missions on the screen, there is some drop in some fps, I play at 60 but at the beginning it drops to 57 56, and then it goes up again, I don't understand what's happening because a few months ago this didn't happen, (but I think the problem is due to the excessive load of the first core) I have tried with HT OFF and disconnecting the core but as I have commented during the first minute of the mission, there are many objects on the screen placed in the editor and with the F4 phantom I have a drop of approximately 5 FPS) my system rtx 4090 i7 12700k 64gb RAM DDR4

same problem, after update sometimes fps instability, RTX 4090 here, before there was no this problem

Hello, have you already implemented the new model pilot in the f18? since I cannot find this information in the latest changelog, unlike the f16 which is implemented thanks greetings

Hello, are there 3 new time presets after the last update 2.9.6? I have 4 new light rain presets Are there plans to introduce more presets? Since there are very few, greetings

A complete review of internal and external textures is necessary.

Hello, is there a review and update of external and internal textures planned to bring the p51 to the graphic standard that we have today in DCS? Thanks

Not work! Thanks!!

I have discovered that the problem is the tobiieye causes incompatibility when you disconnect the eye tracking axes, but only with third party planes, if I disable the device from options the normal camera control works from the joystick, I have tried uninstalling completely and remove controls and it still doesn't work please ED fix this! since it is an update problem!

Hello, I have a strange problem only with all third-party modules, when I unlock the camera to move it with the mouse or with the mapped camera control axis buttons, the camera rotates but immediately returns to the center of the camera!! and the modules cannot be flown! It only happens to me with all the third parties I have tried, for example with JF17, F15, Harrier, C101,F14....., and with all the EAGLE dynamics modules they work correctly! I have checked the controls on my controls and everything is correct! I have tried to repair and uninstall these modules but the same thing happens! only the camera control, the ED modules, F18, F16, A10, Apache etc. work correctly.

The hud brightness not work for me

I don't think it's necessary to post anything else, the problem is simple, the plane tends to get out of control on the landing roll, after the touchdown, when you apply the brakes slowly without actually digging them in, the plane goes left or right, it's hard to stop it, I land slowly, with the speed brake on, and I use the differential brakes to keep The plane is straight, I maintain the angle of attack and the correct speed, but this does not seem to give very good results, since as I have asked, I think it is because the anti skid is not implemented? with other aircraft m2000, f18, f14, a10 etc this does not happen

hello I think this module is one of the best modules we have today in DCS but I think you need a new external 3D model, especially when you are in the cockpit and look towards the wings, you can clearly see the non-polygonal lines, nor straight lines, in the air inlets of the turbines It also has internal details that need tweaking in terms of quality, since the new planes that we have at DCS have much better quality than, for example, the Harrier that has been in production for some time. Have you thought of a 3D rework? thanks greetings

Hello, I wanted to know if the anti skid is correctly implemented? Since this plane deviates completely when landing and braking, it is with the only plane that this happens to me, is there any plan to address this problem? I have seen many old threads from years ago, but we are in 2023 and the problem is still the same? thanks a greeting I wait for an answer

Hello, I can't modify the brightness of the HUD, I have mapped the controls to increase the brightness of the hud and decrease the brightness of the HUD but it doesn't work, it's always the same, does anyone know what happens or how can I fix it? I have installed the latest version of the BETA version thank you

Hello, I can't modify the brightness of the HUD, I have mapped the controls to increase the brightness of the hud and decrease the brightness of the HUD but it doesn't work, it's always the same, does anyone know what happens or how can I fix it? I have installed the latest version of the BETA version thank you

hello I think this module is one of the best modules we have today in DCS but I think you need a new external 3D model, especially when you are in the cockpit and look towards the wings, you can clearly see the non-polygonal lines, nor straight lines, in the air inlets of the turbines It also has internal details that need tweaking in terms of quality, since the new planes that we have at DCS have much better quality than, for example, the Harrier that has been in production for some time. Have you thought of a 3D rework? thanks greetings

I can not enter the game error 502 and 504 the sinai map is no longer available to buy from the E-SHOP-TERRAINS I bought the sinai map, a few hours ago, I can't download it from the module manager

Its down again?

I bought it two hours ago, but I was able to enter the game 15 minutes ago, right now if you go to the website it does not appear to buy from E-SHOP-TERRAINS I can't download it in-game from the module manager either.

Now it works, but it seems that they have disabled the new SINAI module, I bought it a while ago, and right now it does not appear on the website to buy, also now when entering the game there is no option to download it from the module manager Does this happen to anyone else? thank you