YoYo Posted yesterday at 06:51 PM Posted yesterday at 06:51 PM (edited) Currently, we only have a stepping option via buttons (CW and CCW) from +10 to -6 km. Could you also make the elevation control knob an axis? I usually use the throttle slider in the Warthog for this, and we can't configure it that way with the MIG-29. TY. Edited yesterday at 06:54 PM by YoYo Webmaster of http://www.yoyosims.pl Win 10 64, i9-13900 KF, RTX 5090 32Gb OC, RAM 64Gb Corsair Vengeance LED OC@3600MHz,, 3xSSD+3xSSD M.2 NVMe, Predator XB271HU res.2560x1440 27'' G-sync, Sound Blaster Z + 5.1, TiR5, [MSFS, P3Dv5, DCS, RoF, Condor2, IL-2 CoD/BoX] VR fly only: Meta Quest Pro
AeriaGloria Posted yesterday at 08:51 PM Posted yesterday at 08:51 PM An axis that steps through the knob positions? Black Shark Den Squadron Member: We are open to new recruits, click here to check us out or apply to join! https://blacksharkden.com
YoYo Posted yesterday at 08:53 PM Author Posted yesterday at 08:53 PM 1 minute ago, AeriaGloria said: An axis that steps through the knob positions? Correct. It may skip. Webmaster of http://www.yoyosims.pl Win 10 64, i9-13900 KF, RTX 5090 32Gb OC, RAM 64Gb Corsair Vengeance LED OC@3600MHz,, 3xSSD+3xSSD M.2 NVMe, Predator XB271HU res.2560x1440 27'' G-sync, Sound Blaster Z + 5.1, TiR5, [MSFS, P3Dv5, DCS, RoF, Condor2, IL-2 CoD/BoX] VR fly only: Meta Quest Pro
Hammer1-1 Posted yesterday at 09:05 PM Posted yesterday at 09:05 PM well...if one were to do it that way, you could place percentage ranges on an axis and map them as buttons...id have to refresh my memory on how to do it, but both virpil and vkb software allow you to do just that. Intel 13900k @ 5.8ghz | 64gb GSkill Trident Z | MSI z790 Meg ACE | Zotac RTX5090 | Lian Li 1300w psu | Slaw RX Viper 2 pedals | VPForce Rhino/VKB MCE Ultimate + STECS Mk2 MAX / Virpil MongoosT50+ MongoosT50CM | Virpil TCS+/ AH64D grip/custom AH64D TEDAC | Samsung Odyssey G9 + Odyssey Ark | Next Level Racing Flight Seat Pro | WinWing F-18 MIPS | No more VR for this pilot. My wallpaper and skins On today's episode of "Did You Know", Cessna Skyhawk crashes into cemetery; over 800 found dead as workers keep digging.
YoYo Posted 16 hours ago Author Posted 16 hours ago 8 hours ago, Hammer1-1 said: well...if one were to do it that way, you could place percentage ranges on an axis and map them as buttons...id have to refresh my memory on how to do it, but both virpil and vkb software allow you to do just that. I'm using TARGET, so it's doable, but you'd still have to raise the axis above 0 to gradually increase the angle upward. If there were positions from -6 to +10 in the control settings, then it would be possible, but not if there's only CW and CCW like now. Webmaster of http://www.yoyosims.pl Win 10 64, i9-13900 KF, RTX 5090 32Gb OC, RAM 64Gb Corsair Vengeance LED OC@3600MHz,, 3xSSD+3xSSD M.2 NVMe, Predator XB271HU res.2560x1440 27'' G-sync, Sound Blaster Z + 5.1, TiR5, [MSFS, P3Dv5, DCS, RoF, Condor2, IL-2 CoD/BoX] VR fly only: Meta Quest Pro
Recommended Posts