Fakum

yes, that is currently the case, but thanks

I recently upgraded to a LG - UltraGear 38" IPS LED UltraWide HD G-SYNC Monitor and a 2080 Ti FTW3 GPU. Graphics settings in DCS are pretty much maxed out, and I run a pretty solid 60 – 80 fps. My monitor refresh rate is set to 120 hz, with G-Sync on. I get screen tearing. I have no why, and no idea if it’s a monitor or GPU issue. I don’t have a spare monitor or GPU to swap out to test. I also do not have any other games/sims. Any idea on how to troubleshoot? Thanks,

Thanks for clarifying that for me. Its nice to know then that parts are still available.

Parts received. I ordered (2) Antenna pots, so I would have a spare. the 1st one I installed did not work as it should, I installed the 2nd (spare) and it worked great! I will have to deal with them about that. I also ordered a Speed Break switch. (T9 & T10). I have a question, and I dont recall, or can I find an answer online, or in the manual. The new switch has 3 positions. Center, moving one way is only momentary (does not lock in place), move the other and it stays in a fixed position (locks in place)? Is that how the speed brake is supposed to work? I thought it was supposed to mechanically stay in any position you set it in?

Thank you Rudel, I did not want to waste a few days trying if it were not applicable. Guess i will just map a different way,,, thanks again

I appreciate the feedback guys, but I still have 1 open question from page 2, and that is, would I be wasting my time trying to get Logical flags to work? Again, I am willing to learn, but ifs the wrong application, I dont want to waste a few days, thanks.

Yeah, I can get the toggle to work, just not in addition to using a modifier. That syntax in the 3rd shot, thats more scary then Foxy LOL. I have a headache already,,,, Thanks though

Thanks for the advise. I have to be honest, I tried to convert to the Target software about 8 years ago,, I was completely frustrated with a configuration I was trying to do, I couldnt get it to work in Target after a couple of weeks of help on the forums, I managed to achieve it through Foxy, and I never looked back.

Ok, thats good to know. So I recall seeing "Logical Flags" (Example Below) in older profiles that I once downloaded and used. I dont really know how I would make use of these, but Im willing to try and learn if they will work if written correctly for that switch. Would I be wasting my time or is this approach for that switch workable? Thanks E.G. BTN H3U /I KD(X9) DLY(200) KU(X9) /O KD(X8 ) DLY(200) KU(X8 ) DEF X10 DELAY(500) H3U AND S3 DEF X11 DELAY(500) H3U AND NOT S3 DEF X12 NOT H3U AND X8 DEF X13 NOT H3U AND X9 BTN X10 Trimmerreset BTN X11 /H Trimmer BTN X12 HoverOn/Off BTN X13 Wheelbrakeparking BTN H3D /I TrackIR_Precision /O TrackIR_Center DEF X4 DELAY(500) H3D AND S3 DEF X5 NOT H3D AND X1 DEF X6 NOT H3D AND X2 DEF X7 H3D AND S3 BTN X4 Axis_Reset BTN X5 Axis_Lock BTN X6 Axis_Unlock BTN X7 /P Axis_Lock Axis_Trim /R Axis_Unlock

I am trying to use my "DogFight" switch to control the Radiator Dampers on the P-51D. I get the Radiator Cooling Damper to work just as I want it to, but when I use the (S3 Modifier for the "IN" for the Radiator Oil) same switch in the Modifier Mode, the switch does not HOLD in position once the S3 button is released? Here is my current config: Rem ################################################ Rem T7-T8 : Rem ################################################ BTN T7 /I /H /P Radiator_oil_Close /R Radiator_oil_Auto /O /H /P Radiator_coolant_Close /R Radiator_coolant_Auto BTN T8 /I /H /P Radiator_oil_Open /R Radiator_oil_Auto /O /H /P Radiator_coolant_Open /R Radiator_coolant_Auto

Yes, so back in february, I tried the Rift CV-1, took it back for the same problem, and actually at the time, I only had a 980 Ti. So I thought that was the issue. And I also wore glasses for distance and another script for PC monitor, but I see perfect in front of me without glasses. I tried all variations back then as well. Fast forwarding to now... I have tried with no glasses, my PC Monitor glasses, and my distance/driving glasses,,, all fail.

I certainly understand your point. My expectations are derived from conversations i have had with fellow players (This was all Rift-S based discussion in recent months), and also reading alot of posts and reviewing YouTube reviews. A couple of folks I commonly fly with have lower spec PCs then I do, certainly lower spec GPU and they were advising me that they could see all of the Huey gauges and text clearly. Huey is what I have been testing with, I mean, if they have clarity, I should expect the same. So I dont think my expectations are too high in my opinion. I am extremely disappointed, I was so looking forward to VR!

Throwing in the towel on the Odysses+,,, Will have to look at another option, here is my final post over at WMR: "Well,, I tried for a few more hours, no luck for me. Cant get the instruments and instrument text clear. played with both Pixel Density and that slider in Steam VR, even different glasses. Hard to believe wit hall this horse power, I cant get a clear picture. Unless there is something in NVidia inspector I need to change, this is going back tomorrow! I will say this, the Rift-S was so much easier to deal with, had more room for glasses, and just looked and felt so much better than this (For Me). To bad it didnt work out either, I took that back because I thought it didnt have IPd Manual Adjustment, and I though that was the issue?"

Well,, I tried for a few more hours, no luck for me. Cant get the instruments and instrument text clear. played with both Pixel Density and that slider in Steam VR, even different glasses. Hard to believe wit hall this horse power, I cant get a clear picture. Unless there is something in NVidia inspector I need to change, this is going back tomorrow! I will say this, the Rift-S was so much easier to deal with, had more room for glasses, and just looked and felt so much better than this (For Me). To bad it didnt work out either, I took that back because I thought it didnt have IPd Manual Adjustment, and I though that was the issue?

Just confirming here, I plugged in the Odeysses+, WMR prompted setup and completetion, then install Windows Mixed Reality for steam VR 19.1.3 from steam. Then when ready to play, open WMR for Steam VR, then open DCS correct? I hope Im doing something wrong because this is awful! 2 screens on my desktop 1 to the far left is Mixed Reality Portal, the other in the center I presume to be WMR for Steam VR? Presentation screens are wicked choppy until I get in the game. Mouse works occasionally I just want to make sure my startup procedure is correct? Thanks

Installed Odeysses last night, WMR setup went ok, Steam VR was more difficult. Anywho, the bottom line so far is that I still cant read the Text/Labels Guages clearly. Too much to post in here, and I dont want to turn this into an Oddeysses + thread, as one already exists basically, so I posted the specific Oddeysses+ problems over at. https://forums.eagle.ru/showthread.php?t=208086 To be continued, thanks guys

@Baldrick33, Thanks, but as I stated, I tried with and without glasses. @Unclezam, Thanks, I had no idea we could run that high, I certainly have nothing to loose trying that. Regarding the Breaking News info, since i just downloaded and installed last night, I would imagine I have the latest version? I will check tonight. I will say this, 1st I had to setup WMR, then I understood that I had to download and install WMR for Steam VR. I had difficulty finding that while logged into Steam, even while looking for it in Steams search box. Never did find it there, I wound up doing a google search and navigated through that to install it. Install was a pain! It kept asking me to plug in the headset when it was already plugged in and working in WMR? I wound up having to pull the cables a few times to get it. Then sometimes the mouse curser works when the headset is on, sometimes not? In DCS/VR Tab, I have the mouse selected to work both in the game and outside, controllers off. I would have to take the headset off my head at point it at the monitor to use the mouse in DCS. Also, when DCS loads, the screens you see are distorted and flicker. Once in the game, all is well? My maiden flight with Steam VR and Odeysses was extremely frustrating,,, will give it another go tonight. Thanks,

I just installed Odyssey+. Last week I had the Rift-S and couldnt dial in to see the text on the gauges clear, thought it was because I measured my IPD at about 70 to 72, and couldnt make the manual adjustment on the Rift-S. Today, I setup the Odyssey+, and Im having the same difficulty? I wear glasses to see far away, I also have computer glasses, dont need glasses for up close. My DCS settings are mostly all maxed out and run great FPS on my monitor. I tinkered around for a long time adjusting pixel density, between 1 and 2.3, and also trying different glasses. Gauges are not very legible? I also went into Steam and moved the slider up to 140 as suggested elsewhere. I have no idea what more adjustments I could possibly make, but feel i am missing something? Thanks for any help.

You are correct sir about it being about BS1, and thanks for the response,, that is a relief to know.

I just stumbled upon another post where someone asked how the black Shark looked in VR,,, the response was that the Black Shark is NOT compatible for VR? So I dont know if this is the correct place to ask this, but if that is true, is there a list of modules that do not support VR? Id like to know which ones dont? Thanks,

I have an old Steam Login, but I dont have Steam installed on my PC specifically, so I still need to install Steam even though I can log into it?

IPD in DCS is completely different than Inter Pupil distance, and discussed in depth elswhere in the forums. And yes, alot of folks mistaken it for Inter Pupil distance. Thanks for the feedback on the Steam VR, I dont know what it means yet, but I will, LOL

Nothing stressful other than trying to run my settings all as high as possible. And I also have tried to isolate DCS to cores 2 & 3 myself,,, thanks.

That would have been the 1st iteration, cv1, the 2nd iteration , S, does not

Alrighty then,,, thanks