Deadman

Hey Thanks so much for making full functioning cockpit building possible.!! Cheers DM

an oldie but very good https://www.facebook.com/122ndFighterWing/videos/912283168823718/

These HGU 55 helmet wraps look very good. https://www.moody.af.mil/News/Article-Display/Article/2092423/helmet-wraps-foster-pride-in-pilots/

https://www.liveleak.com/view?t=9aa_1518447544

Check out Hans's A-10 plans. for the shell

NO this was designed to Fusedspine33 spec you may find an acceptable 5 inch square or 7 inch sq tft display with a driver board either on the net some place i have seen them but do not have a link. I could easily adapt the bezel for either

You can't go wrong with good quality switches and rotaries.

they are painted hard acrylic (Plexiglas) Clean with goof of or a grease cutter just spry it and clean with blue shop towels they are not abrasive as paper towels for the kitchen.If it does not feel grease or it not to dirty I use vinegar and water and a q tip to clean the white lines and face of the panel

Hey Thanks so much for posting they look great I am so pleased they assembled as we planed.

Hum a page about building Cockpits for DCS think it has been done before. Hence the name Home cockpits. Just saying plus there are all ready several cock builder groups on FB

EBay

The member I made the models for will post a build with picture as soon as he gets the three bezels . Thanks for the kind word I can't wait to see the build.

Just made two bezels for one of our member and he suggested i let you guys know they are on my Slapways site. they are designed for low cost snap in push button and rocker switches https://www.ebay.com/itm/50Pcs-Black-PB04-14-x-14mm-Square-2Pin-Momentary-SPST-Mini-Push-Button-Switch/183620506764?hash=item2ac0a2948c:g:4f0AAOSw5wNcL2Ra https://www.ebay.com/itm/SPDT-KCD1-Mini-Rocker-Switch-Momentary-On-Off-On-6A-250VAC-USA-SELLER/292224433140?hash=item4409eefbf4:g:3pMAAOSwXoxaa7W~ Honeywell RV6 potentiometer and GRAYHILL SERIES 50 rotary switch all of these are on eBay so just do a search https://www.shapeways.com/product/8K6HDPANL/f-18-mpcd-avab?optionId=141494826&li=shops https://www.shapeways.com/product/FYXXVQX6H/f-18-ddi-bezel?optionId=141160580&li=shops

Here is a best guess on the F-18 know for the Inter lighy panel https://www.shapeways.com/product/XALJG9ENB/f-18?optionId=140737907&li=shops If any one can make a better closer picture of it from the sim and points out any difference I will correct the model.

New chart dimmer knob listed as 8505 up on the site it is a bit different than the f-16 style straighter sides and a bit beefier

The rebuilt knobs are in the F-18 section I will look over the next couple of days for a real picture of the last knob.

I can remake those two knobs wit 1/8 inch shafts no problem. TT155 all ready has a .125 inch (1/8) shaft hole.

Ok 1/8 inch shaft no problem would you want an out side diameter of .65 or.88 inch ? do you have a better picture of the warning caution light dimmer knob?

you need to purchase the knobs from a distributor. They rarely have the back lit gray knob for aircraft and if they do the knob are $30 and up last time i checked several years ago. I have A-10-C and a few F-16 items all based on real knobs. if you are looking for some thing else let me know and I can add it to the site. https://www.shapeways.com/shops/a-10c-warthog-supplies

What do you mean by Button the cap ( what you push ) or the switch?

Found a couple of good videos about building on one of my favorite Youtube channels.

Here is the data sheet you are missing for the landing gear panel Taxi light Switch Honeywell 2TL6-1 as included in the switch list.

ok