Jump to content

[NEED TRACK REPLAY]Weird radar behavior


fmedges
 Share

Recommended Posts

This once is a little hard to explain and I have a track file which I’ll attach once I get back to my desktop. The radar started to act strangely in the air. Went from tws to rws and tried to undesignate but that wasn’t working so I put the radar in standby. I landed and on the runway turned off nws and then back on and my radar started tracking targets while I was on the ground and it was in standby. I had the shoot cue rolling down the runway. I’ll attached a track file soon. The server I was n cuts off the last 10 minutes, but hopefully this will still provide some good data. The file was too big to attach so here is the link.

 

https://www.dropbox.com/s/72sabzc6zhu1am2/Gunslinger%20Training%20Command-20200429-203400.trk?dl=0


Edited by fmedges
Link to comment
Share on other sites

+1 I have this issue too. It is like when I press NWS switch, radar in TWS will display a target memory. It will never leave unless I switch radar OFF and back on. But still, it persists if I press NWS.

ASUS N552VX | i7-6700HQ @ 2.59GHz | 16 GB DDR3 | NVIDIA GF GTX 950M 4 Gb | 250 Gb SSD | 1 Tb HD SATA II Backup | TIR4 | Microsoft S. FF 2+X52 Throttle+Saitek Pedals | Win 10 64 bits

Link to comment
Share on other sites

  • 3 weeks later...

I think I’ve had the same issue. I don’t get it all the time, but have had it consistently on the Dire Straits mission. As soon as I pull up TWS it locks a memory target no where near my scan zone. Reset doesn’t clear it. Haven’t tried turning the radar off and back on

Link to comment
Share on other sites

  • 2 weeks later...

F-18 Radar turns ON after landing on SC

 

Not sure if this was already reported and if this is a SC bug or an F-18 bug, but a few seconds after I land on SC the radar locks on a target and it stays locked even if I turn it off.

 

Track file too large to attach. So I uploaded on dropbox.

 

Link here: https://www.dropbox.com/s/w0qfq13wm7s03x1/F-18C_Intercept_PG.trk?dl=0

 

Intel i7 12700k / Corsair H150i Elite Capellix / Asus TUF Z690 Wifi D4 / Corsair Dominator 32GB 3200Mhz / Corsair HW1000W / 1x Samsung SSD 970 Evo Plus 500Gb + 1 Corsair MP600 1TB / ASUS ROG Strix RTX 3080 OC V2 / Fractal Design Meshify 2 / HOTAS Warthog / TFRP Rudder / TrackIR 5 / Dell U2515h 25" Monitor 1440p

Link to comment
Share on other sites

It did that even before SC, once landed, after folding the wings when I pressed NWS to have hi gain, it would lock on a target. You have to press the reset OSB on the radar page to drop the contact, I hope they'll fix this thing soon.

Link to comment
Share on other sites

Yeah this happened to me many times before the SC as well after landing. Even happened on land AB's too.

i9 9900k @5.1GHz h100i |Asus ROG Strix Z390 E-Gaming | Samsung NVMe m.2 970 Evo 1TB | LPX 64GB DDR4 3200MHz

EVGA RTX 3090 FTW3 Ultra | Reverb G1  | HOTAS Warthog | Saitek Flight Pedals

Link to comment
Share on other sites

So funny that they labeled this thread with a [NEED TRACK REPLAY] even though I have provided one on my post above.

 

Intel i7 12700k / Corsair H150i Elite Capellix / Asus TUF Z690 Wifi D4 / Corsair Dominator 32GB 3200Mhz / Corsair HW1000W / 1x Samsung SSD 970 Evo Plus 500Gb + 1 Corsair MP600 1TB / ASUS ROG Strix RTX 3080 OC V2 / Fractal Design Meshify 2 / HOTAS Warthog / TFRP Rudder / TrackIR 5 / Dell U2515h 25" Monitor 1440p

Link to comment
Share on other sites

So funny that they labeled this thread with a [NEED TRACK REPLAY] even though I have provided one on my post above.

 

Even fmedges provided one. Since both of you said that the track was too big to attach on the forum, I think they need a new one because big tracks in DCS always get corrupted and don't show what actually happened.

 

We need to provide a short track, maybe from a premade mission with just a straight in landing, so that the track doesn't (hopefully) get corrupted.

Link to comment
Share on other sites

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...