sobe Posted March 20, 2022 Posted March 20, 2022 Why do I keep getting a low rpm warning when I go into a hot Apache and try to hover? When I am in the CPG seat and try to control the Apache with George, I get the George command circle and George's voice, but the Apache does not go up. What am I doing wrong? Trackir4 using the latest Trackir 5 software, Win10 Pro [Creator Update] updated from Win7Pro Pro 64Bit, Intel® Core™ i5-2500 3.30 GHz 6M Intel Smart Cache LGA115 , GigaByte GA-Z68XP-UD4 Intel Z68 Chipset DDR3 16GB Ram, GTX MSI Gaming 1060 [6 GB] Video Card, Main Monitor 1 on left 1920x1080 Touchscreen Monitor 2 on right 1920x1080 .
Feuerfalke Posted March 20, 2022 Posted March 20, 2022 9 minutes ago, sobe said: Why do I keep getting a low rpm warning when I go into a hot Apache and try to hover? When I am in the CPG seat and try to control the Apache with George, I get the George command circle and George's voice, but the Apache does not go up. What am I doing wrong? It happens when you pull the collective too hard and too fast and, of course, if the throttle-level of your engines is too low. (check left console) Did not try CPG with George as pilot, yet. In general: Commands in the inner circle are accessed by a short press, commands in the outer circle are activated via long press. Maybe that will make a change. MSI X670E Gaming Plus | AMD Ryzen 7 7800X3D | 64 GB DDR4 | AMD RX 6900 XT | LG 55" @ 4K | Cougar 1000 W | CreativeX G6 | TIR5 | CH HOTAS (with BU0836X-12 Bit) + Crosswind Pedals | Win11 64 HP | StreamDeck XL | 3x TM MFD
Baldrick33 Posted March 20, 2022 Posted March 20, 2022 Have you mapped the up, down. left & right controls to the George AI helper controls section? AMD 5800X3D · MSI 4080 · Asus ROG Strix B550 Gaming · HP Reverb Pro · 1Tb M.2 NVMe, 32Gb Corsair Vengence 3600MHz DDR4 · Windows 11 · Thrustmaster TPR Pedals · VIRPIL T-50CM3 Base, Alpha Prime R. VIRPIL VPC Rotor TCS Base. JetSeat
sobe Posted March 20, 2022 Author Posted March 20, 2022 yes Trackir4 using the latest Trackir 5 software, Win10 Pro [Creator Update] updated from Win7Pro Pro 64Bit, Intel® Core™ i5-2500 3.30 GHz 6M Intel Smart Cache LGA115 , GigaByte GA-Z68XP-UD4 Intel Z68 Chipset DDR3 16GB Ram, GTX MSI Gaming 1060 [6 GB] Video Card, Main Monitor 1 on left 1920x1080 Touchscreen Monitor 2 on right 1920x1080 .
ED Team Solution Raptor9 Posted March 20, 2022 ED Team Solution Posted March 20, 2022 You may be carrying too much weapons/fuel for the environment you are in, like hot or high altitude locations. Try reducing the payload you are loaded with and see if that works. Afterburners are for wussies...hang around the battlefield and dodge tracers like a man. DCS Rotor-Head
salsantana Posted March 20, 2022 Posted March 20, 2022 30 minutes ago, Feuerfalke said: It happens when you pull the collective too hard and too fast and, of course, if the throttle-level of your engines is too low. (check left console) Did not try CPG with George as pilot, yet. In general: Commands in the inner circle are accessed by a short press, commands in the outer circle are activated via long press. Maybe that will make a change. Not to derail from topic, but I was just now wondering about the Apache's throttles...... far as I know and/or presume, the throttles in helicopters are kept at full while in flight and of course in takeoffs, while power is exclusively controlled by collective........ (this is a question).
jonsky7 Posted March 20, 2022 Posted March 20, 2022 12 minutes ago, salsantana said: Not to derail from topic, but I was just now wondering about the Apache's throttles...... far as I know and/or presume, the throttles in helicopters are kept at full while in flight and of course in takeoffs, while power is exclusively controlled by collective........ (this is a question). Yes, same in Apache, put throttles to flight position, don't touch them again till landing. ( more or less) 1
Recommended Posts