Need help sourcing a USB cable

Hammer1-1 · November 2

I have a MongoosT-50CM throttle that needs a replacement USB cable. Apparently its proprietary or something and a local repair shop nearby cant even splice repair my current one. Any help locating a replacement would be appreciated...

speed-of-heat · November 2

Have you tried contacting Virpil directly?

speed-of-heat · November 2

https://virpil-controls.co.uk/shop/accessories/cables

Hammer1-1 · Sunday at 06:02 PM

because Im hoping someone can source me a 5 pin USB-A cable that doesnt have to come all they way from lithuania and I can fix this week. I did email them today and they're happy to ship me one...but USPS hasnt been too friendly with my packages that have come or gone out of country this past year either coming home damaged or not at all. Id like to keep customs out of it if possible.

Also should point out that this isnt the round connector; its a clip on 5 pin bar that you pin onto the motherboard rather than into the base of the control. Its an older throttle, something Virpil quit making about 5 years ago.

Edited Sunday at 07:12 PM by Hammer1-1

Hammer1-1 · Sunday at 11:30 PM

heres a picture of the motherboard attach bar.

Nightdare · Monday at 04:17 PM

Shouldn't be that hard to get that connector on a new USB cable with a bit of solder and heat shrink, I should know, I once replaced all the wires on my Saitek Rhino Throttle

unless it's the connector itself, but I believe that's a very common JST connector anyway

(Though I'll admit that finding local shops still stocking small electronic parts are getting rarer every year)

Edited Monday at 04:19 PM by Nightdare

Hammer1-1 · Tuesday at 12:30 AM

8 hours ago, Nightdare said:

Shouldn't be that hard to get that connector on a new USB cable with a bit of solder and heat shrink, I should know, I once replaced all the wires on my Saitek Rhino Throttle

unless it's the connector itself, but I believe that's a very common JST connector anyway

(Though I'll admit that finding local shops still stocking small electronic parts are getting rarer every year)

I just dont know what kind of connector this is. I took it to an electronics repair place and they couldnt source a cable for me. I dont think this one is going to be hard to find, but Ive no idea about this stuff. This is why Im asking, I dont know what kind of cable I need. I just know its a 4 pin USB 2.0 cable with a 5th wire thats shielding.

Edited Tuesday at 12:31 AM by Hammer1-1

jnr4817 · Tuesday at 12:42 AM

looks like a jst ph or sh 5 pin connector. There are several places online that sell these. Installing is very simple and some even come with a tool.

JST, PHR Female Connector Housing, 2mm Pitch, 5 Way, 1 Row.

Got a pic of the other side.

Edited Tuesday at 12:44 AM by jnr4817

Hammer1-1 · Tuesday at 02:26 AM

1 hour ago, jnr4817 said:

looks like a jst ph or sh 5 pin connector. There are several places online that sell these. Installing is very simple and some even come with a tool.

JST, PHR Female Connector Housing, 2mm Pitch, 5 Way, 1 Row.

Got a pic of the other side.

heres that.

jnr4817 · Wednesday at 01:26 PM

Yeah, I feel like I found your connector depending on where you live. You should be able to get one within the next couple of days. If not same day now you may have to buy 100 but it’s easily fixed.

Hammer1-1 · Thursday at 05:40 PM

is there a way I can salvage the bar I have? I just ordered a couple, not sure what tool I need to put the pins in though.

Edited Thursday at 05:41 PM by Hammer1-1

Scott-S6 · Thursday at 05:49 PM

9 minutes ago, Hammer1-1 said:

is there a way I can salvage the bar I have? I just ordered a couple, not sure what tool I need to put the pins in though.

You could just cut that end off and solder it to a USB cable

Hammer1-1 · Thursday at 06:52 PM

bold of you to assume I can solder....I would have done that already if I was actually any good at it.

Scott-S6 · 2025-11-07T05:03:50Z

10 hours ago, Hammer1-1 said:

bold of you to assume I can solder....I would have done that already if I was actually any good at it.

So get crimp connectors or a terminal block. This isn't difficult. You can even get terminal blocks that don't require you to be able to use a screwdriver.

Edited yesterday at 05:07 AM by Scott-S6

Hammer1-1 · 2025-11-07T15:54:42Z

Im pretty sure a terminal block is a bit much for just five 22awg wires. Ive thought about using crimp connectors and that would be just a bigger mess than its worth doing. It would work, yes....but thats like sticking a band aid on a bullet wound. Id rather just replace the connector or the entire wire and keep it clean. I got enough wires to worry about where cable management is already a nightmare. I got a new connector arriving, just need to find a tool to set the wires.

Edited 19 hours ago by Hammer1-1

Scott-S6 · 2025-11-08T06:19:36Z

14 hours ago, Hammer1-1 said:

Im pretty sure a terminal block is a bit much for just five 22awg wires. Ive thought about using crimp connectors and that would be just a bigger mess than its worth doing. It would work, yes....but thats like sticking a band aid on a bullet wound. Id rather just replace the connector or the entire wire and keep it clean. I got enough wires to worry about where cable management is already a nightmare. I got a new connector arriving, just need to find a tool to set the wires.

No, you would use a terminal block that is specifically for wires that size. What would be overkill about it?

Have you measured the pin spacing to make sure you have the correct connectors coming?

You need a JST crimping tool. They come in different sides, make sure you get one that covers your wire size.

Edited 4 hours ago by Scott-S6

Sign In

Need help sourcing a USB cable

Recommended Posts

Hammer1-1

speed-of-heat

speed-of-heat

Hammer1-1

Hammer1-1

Nightdare

Hammer1-1

jnr4817

Hammer1-1

jnr4817

Hammer1-1

Scott-S6

Hammer1-1

Scott-S6

Hammer1-1

Scott-S6

Recently Browsing 0 members