Jump to content

Recommended Posts

Posted

...and another-one how it works in-game with a FFB set-up:

 

 

Note: There is no spring-force on the Cyclic when the trim button is hold down.

Posted (edited)

Note: There is no spring-force on the Cyclic when the trim button is hold down.

Yes and this is the thing that is still broken in DCS 1.2.3 on the Logitech G940!

Unless you use Sim FFB,By average_pilot

Edited by jib

Mods I use: KA-50 JTAC - Better Fire and Smoke - Unchain Rudder from trim KA50 - Sim FFB for G940 - Beczl Rocket Pods Updated!

Processor: Intel Q6600 @ 3.00GHz

GPU: GeForce MSI RTX 2060 6GB

RAM: Crucial 8GB DDR2

HDD: 1TBGB Crucial SSD

OS: Windows 10, 64-bit

Peripherals: Logitech G940 Hotas, TrackiR 5, Voice Activated commands , Sharkoon 5.1 headset. ,Touch Control for iPad, JoyToKey

  • 1 month later...
Posted

Trim Controle indicator

 

Hello

I have a strange problem here.

In BS2 i can open the Controle Indicator to adjust my trimmer, but in Dcsw 1.2.3 BS2 it doesnt popup.

But in the option key config tab it seems like the key combo works because after hitting the keys, the high lighted search beam jumps to the right commandline [ show controlle indicator].

Is there something i need to check/uncheck or adjust in a lua file?

Posted

Clyber, I just thought about it rightnow; Do you use multi-monitor? May be it appears, but you can't see because of multi-monitor settings or etc...

Intel i7-14700@5.6GHz | MSI RTX4080 SuperSuprimX | Corsair V. 64GB@6400MHz. | Samsung 1TB 990 PRO SSD (Win10Homex64)
Samsung G5 32" + Samsung 18" + 2x8"TFT Displays | TM Warthog Stick w/AVA Base | VPC MongoosT-50CM3 Throttle | TM MFD Cougars | Logitech G13, G230, G510, PZ55 & Farming Sim Panel | TIR5 & M.Quest3 VR
>>MY MODS<< | Discord: Devrim#1068

Posted (edited)

Devrim your right i use multimonitor and Emc for exports. Ive learned that Multimon indeed can have some effect on the Controle indicator.However its strange that the controle appears in Bs2 with multimon but not in dcsw bs2. I dont have a clue witch file was adjusted without my knowledge,or witch file i should configure.

Edited by Clyber
Posted

To relocate your control indicator, see this post.

 

http://forums.eagle.ru/showthread.php?p=1409442#post1409442

 

There is a little bit of trial and error involved but it is not difficult.

ASUS ROG Maximus VIII Hero, i7-6700K, Noctua NH-D14 Cooler, Crucial 32GB DDR4 2133, Samsung 950 Pro NVMe 256GB, Samsung EVO 250GB & 500GB SSD, 2TB Caviar Black, Zotac GTX 1080 AMP! Extreme 8GB, Corsair HX1000i, Phillips BDM4065UC 40" 4k monitor, VX2258 TouchScreen, TIR 5 w/ProClip, TM Warthog, VKB Gladiator Pro, Saitek X56, et. al., MFG Crosswind Pedals #1199, VolairSim Pit, Rift CV1 :thumbup:

Posted

Cichlidfan and Devrim, i fixed it Thanx for patiently and kindly helping me out because i really needed the controle indicator. You guys are great

Posted

I think is "broken" only for rudders and only for FFB users.

 

If you don't forget to put the stick to center within 0.5 seconds with "center trim" unticked on Misc Options it works quite OK. With that option "On" you have to recenter the stick so input will be taken into account. For FFB apparently there is no delay for rudders no matter the "center trim" state in Misc Options so the helicopter will jolt violently depending on speed, amount of rudder at that moment etc. Best avoidance is to trim often and quickly release rudders when releasing trim button. Or unchaining the rudders from trim with PeterP mod.

[sIGPIC][/sIGPIC]

I5 4670k, 32GB, GTX 1070, Thrustmaster TFRP, G940 Throttle extremely modded with Bodnar 0836X and Bu0836A,

Warthog Joystick with F-18 grip, Oculus Rift S - Almost all is made from gifts from friends, the most expensive parts at least

Posted (edited)

i have it unchained its a different thing, where the autopliot trims 1st of sorts and then the inpu of the virtual joystick comes making it over trim, ill post tracks

 

 

EDIT: here are two tracks showing whats happening when you trim on a normal joystick at the default trim speed, and on a ridiculously slow speed, you can see that when the virtual joystick input comes into play it causes the helicopter to over trim.

Default Trim Speed.trk

Trim Speed 0.5.trk

Edited by karambiatos
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...