Denwagg

FCR is NOT working fine Tanks out in the open at eye level. FCR does not find them before they are visible to naked eye. Less than 2km away. Used default Syria map weapon range, loaded Lima's. Much better range before latest patch. Can duplicate on other created missions

Same here, Targets Ident on FCR, Switch to Battlemap, CAQ target, Sight Select from FCR to TADS. Select Slave. CRASH dcs.log

I can confirm. FCR On, CAQ FCR Contact in BM Map, Switch to SS TADS. When I press slave button dcs crashes.

Same here even with light loads <17000 lbs from Front Seat George is not holding steady heading. In addition he sometimes continues to fly at 40 knots even when commanded to go to hover.

In special settings set ihadss to Left or right eye only Regards

ignor comment

When I undervolted My Clock speed went from 1920 to 2010 Mhz and temps went down from 83 to 65. So I gain performance and lowered the heat and wear on my gpu. Its a win win situation Regards

Anyone that has a high end Nvidia Graphics 3080, 3080 ti, 3090, 3090 Ti. You really ought to download MSI Afterburner and Learn how to undervolt you gpu. Below is a screen shot of my system. Everything in DCS is MAX 3440x1440, AH64D, Syria, Quickstart, Hot Start default miz Its really easy to learn you just tweak a graph in Afterburner. and then test it for lockups. It will not hurt your computer or GPU in any way. My 3090 Ti went from core clock 1920 to 2010 Mhz GPU power 445 to 335 Watts Temp from 83 to 65 C Voltage from 1.020 to .920 volts Stable no crashes Regards

Opencomposite updated a dll today. DCS crashed every time i tried to stsrt in vr. Finally disabled opentoolbox kit restarted in safe mode reset all to defsult. Restarted normally and that fixed the problem Regards

Same for me. If I Create a mission takeoff from parking hot, gun is aligned properly. If I change that same mission to on the ramp and startup manually boresight IHASS, gun is way out of alignment. Not a ranging issue way off to the right Syria - Gazentep_AH-64D.miz Will upload track file tomorrow

I understand now when you go up or down in percent both increase frame rates Regards

Well number 80% and fps not exact but if I lower upscaling percent framerates decrease

I don't understand ! I have a hp reverb g2 with wmr, openxrcomposite , openxr tools and openxr toolkit installed (rtx 3080 ti) When I increase upscale from 100 to 150% my framerate goes up from 30 to 50 fps. When I decrease upscaleing from 100 to 80 percent my framerate decreases from 30 to 25 fps Same quickstart mission AH-64d Syria ready on the ramp I thought this was suppose to be opposite to what is happening on my system Regards

Over a year ago I worked on setting up my three monitors to use in dcs only to discover that there are many issues that could not be resolved unless my Primary Monitor was the left most Monitor for 0,0 location. Is this still an issue or have most limitation of primary Monitor location been resolved ?

Parking brake shows the handle releasing but it is not releasing. No showing up on the controls indicator either

Thank you Will try tonight

Ok thks for comments I will try to to figure out what I am doing wrong If I am in pilot seat with ihadss on NV off and I want to go to copilot seat with tads on the tedac What Is the correct procedure

When I go to cpt tedak is on c-hud. The tads button on the tedak will not change the video to tads rhg ss tads does not work either I have to turn on nvs and then turn it off. And then I can use rhg ss tads to turn on tads video on the tedak Regardless. With nvs off shouldn't the tads button on the tedak turn on tads video on the tedak. I guess the question is when you go to cpt position and tedak video is on c-Hud. What is the correct way to change video to tads

Yep I have it bound to RHG select tads does not work unless I toggle NVS switch in copilot seat That does not solve the button on the tedak issue

How do I get the tads and pnvs buttons on top of the tedak unit to work When I go to cpt station today is always showing c-hud. Sight select will not select tads. I have to set nvs to normal then off to select tads

This is what I mean about blocking the fixed sight Its not really blocking it but it does move some from this location. Acq point is also in the HMD set to wp1

If it was any lower it would block the fixed sight location

What purpose does the nose location diamond server in the center of the IHADSS. Can it be turned off. Its clutters up HUD when using fixed mode to fire rockets and guns

Why does torque go up and back down a couple of times when collective increase is smooth

*******Solved******* Swap file set too small. Set to min 24000mb Max 24000 mb Solved