Hamilton

:thumbup: Me too, for the same reason.

YESS, please. Thanks Ares63

Agree... Sad week.

Agree, Yay !!!! :dontgetit:

Agree.

I´m also having exactly the same problem described with both F-18C and A-10C. Thanks.

Thank you so much Mr CZ_BPK (and Mr Scotch75), with your small changes to Mr Scotch75´s instructions, I am now successfully operating MAV F with TGP without any problem. :thumbup:

Thank you guys! :thumbup:

Thank you very much for your opinion sir, I saw a statement just like yours in another forum, where the person also did not remove the screws and had no problem at all. EDIT: I didn´t remove the screws in my new TM F-18 grip with WarBRD and no problems too.

Thanks!

Hi Supmua, so with the new firmware after you create a new TMWH/F18 profile you can then interchange the two sticks (A-10 Warthog and F-18 grip) without having to run the sofware, is that so? Is this still necessary to connect the TM F-18 grip: " Remove the 2 bolts holding the female grip connector in place when attaching TM grips to prevent damage to the connectors." Thanks!

To the OP, just wait.

Dear friends, Please help, I tried 50 times to get this VFX F14 grip working with my VPC WarBRD and no success. I followed these steps: Update firmware, close firmware, Save device profile, calibrate and save and load device profile. Axis work fine (X and Y Pitch&Roll only) but NO other axis or buttons work. I tried with the latest VPC Software 20190930 then the previous VPC Software 20190913 and the buttons still don´t work. I fully inserted the cable to the base, I uninstalled the VPC Software, installed again, ran the Firmware update and nothing, I don´t know what else to do... :( I thank you in advance for any input.

Hi Thomasew, thank you so much for your help. Now the screw has fully engaged with the twist lock, and your´re right it´s into the hole by ~ 7mm.(see pic) The way it is now is fine, but I noticed that it is not fully locked, if I twist my fist (If I apply a certain force) I still can move it , is that so? Thanks!

Hi, see the pic:

Edit: Thank you obious, Virpil has not sent me any instructions, guide, nothing ... Would you please tell me how to lock this grip, I over tightened the screw (clockwise) see pic below, but no matter how hard I squeezed it still didn't lock at all. Thanks!

Indeed, the problem is that I cannot trust the TNT Tracking Status, see the last four days: 24/OCT/2019, 10:55 - Shipment arrived at TNT location - Deliver to 28 OCT 2019 before 06:00PM 25/OCT/2019, 11:58 - Shipment arrived at TNT location 28/OCT/2019, 08:12 - Shipment arrived at TNT location 29/10/2019, 09:24 Shipment arrived at TNT location So, what´s the correct? Sad... :cry:

Hi lunaticfringe, I´m in Brazil now.

I hate TNT! My order was scheduled for today, Friday the tracking status was: 24/OCT/2019, 10:55 - Shipment arrived at TNT location - Deliver to 28 OCT 2019 before 06:00PM Today status: 25/OCT/2019, 11:58 - Shipment arrived at TNT location ?!?!?!?! :huh: so it was a lie that arrived on Oct 24th ? And nobody answer their phone. I had to send them an email and till now NO response... Oh boy... :no_sad:

Thanks for your answer. :thumbup:

Thank you Phantom88 for your review, I had exactly the same impression you mentioned above. :thumbup: By the way, do you recommend the TM F-18? Tks!

Same here, clean configuration.

Excuse me, "Wishlist" ?!? We report something that doesn't agree with Mr Wag's tutorial video and then someone move the thread to Wishlist ? Really?? :huh:

Exactly, certanly it´s not OK the way it is now.

Yes, same here. And yes I see the Wag´s video - besides I know the operation from other sim,but for me in DCS it´s not working.