Avio

I confirm that all volume knobs were ramped up to max, but ATC still very soft. Ground comm was fine though. When hot-start from runway, all volumes are okay.

Through the UFC, is there a way to cycle through ALL Steer Points AND ALL Mark Points back and forth using an assigned joystick button? Having to input manually 3A, M1, 4A, M2, etc., into the UFC while doing hard maneuvering around (single pilot) is quite an acrobatic feat.

When hot-start from runway, all volume is good. But when cold-start, ATC sounded very very soft, even though all volume knobs had been tuned to max. Ground controller volume came through just fine though.

Just discovered that if TPOD is set to PTRAK ON at a target, it would stay solid track without any movement at all. So it could be that when Untracked or Area track, the pod has difficulty trying to track onto something, whereas in PTRK, it has something to latch on.

I find pulling away 6 to 7 nm before turning around for attack seems to help minimize the Tgp drifting away. Also, reduce the G and also throttle back some when nearing the aim point seem to help too, especially when turning around from less than 5 nm.

No I don't have a track, but I recall clearly that all other vehicles could be clearly seen but just not that particular one. Will see if that could be repeated.

I agree the radar is excellent for building an initial relative positional SA, but I'm not sure if from 30 miles it could pick up something as small as a mobile target. Will have to try that out.

I like the one in the A10C too, but the one in the eagle I feel isn't too bad, just kind of look different with that greenish tint all over. The one the A10C uses is great, allowing for instant switching between IR polarity as well as TV mode.

In this day and age of precision satellites and GPS, is the ground radar still any good to have? Most known fixed targets would have their coordinates available, while locating tiny mobile targets with the radar is almost like looking for a needle in a hay stack. The TPOD is much better, though range is certainly more limited. Would be nice to know how it could still be a good asset to use. Two other questions :- 1) When doing PTRK on a moving target, it seems to capture track only when about 7 nm away. But at full zoom, even at 10 nm away the moving image was already very clear and distinct, but somehow still not trackable. Is this right? 2) For tanks, etc., moving at 11 knots, they don't show up in GMT. Is there a minimum speed whereby GMT needs to pick up?

Plus at times the pod FOV would jump around to nearby areas outside of tracked object. Or even when untracked (not tracking), trying to move the FOV towards one direction feels "draggy" and slow to move, even suddenly hopping to another nearby spot on its own.

For something so simple it seems the eagle does it in quite a mangled way ... so I found that to store a patched map and recall later, do these :- 1) To Store >>> Freeze patch / 2) Boxed up STO / 3)Unfreeze and proceed to play with map *** Important -- Leave the STO as BOXED, do not unbox 2) To Recall >>> Freeze / 2) Click NEW -- This brings back the stored map 3) Unfreeze and continue when done

Quite a few of us reported TPOD bouncing around too much whenever the plane maneuver, sometimes even when done gently. Hope this could be looked into.

I encountered this too, then realised it was because Autopilot was ON. Turn that off, and both would appear again.

So the process should be :- 1) Zoom to desired level 2) Freeze and box up STO 3) Unfreeze, move around / zoom in/out of areas 4) To recall previous stored image, click New PB Is the above correct? Thought I tried it, but click on New did nothing.

I am pretty sure I was looking at the spot where the vehicle should be. Vehicles were all added the same way, was able to find and see all except that one.

I find the storing of ground radar and the recalling of the stored image rather confusing to use. Does anyone know the correct sequence of storing an image, go on to do something else on the radar, and then recalling back that stored image?

Yes I confirmed the pod just doesn't seem to hold steady, even when object has already been tracked and designated. Can move around quite a bit whenever aircraft maneuvers.

I commanded the TPOD to look into an area that confirmed (via F10) to have a tank target, but the pod shows up only blank ground, with no tank in it. There was never such problem before the latest patch. In the A10C II, it was the Mav that just could not show up a ground target that has already been made SPI. Anyone else seen this?

I had a tank object made SPI and slaved the Mav to it, but the tank just doesn't show up on the Mav, even when well within range. The Mav MFD just show a blank ground, and thus cannot be locked. On the other hand, in the F15E, it was the TPOD that sometimes cannot show up any ground target vehicle. The A10C's TGP also sometimes could not display a ground vehicle target. There was never such problem before the latest patch. Anyone else seen this?

Ok thanks Klarsnow.

Thanks Klarsnow. Just to clear up some confusion, so it is recommended that in the current DCS F15E, it is advisable to do INS PVU updates especially each time before making a map? I assume the model now is default to EGI. Should I wish to change to INS, how can that be done? Thanks.

Okay noted on that, thanks.

In the video I noticed the 60 degrees check turn is to the left. As the TPOD is mounted on the left, would turn to right be better? Doing that allows me to turn back left after pulling away to continue observing and possibly targeting other targets with the TPOD on the left.

Thanks a lot, Hatman, for the very illuminating advice. Pardon my ignorance, but how does one switch between MN and EGI as default? Or is EGI already the default? On the radar screen, it shows as MN at the top left screen. And for INS PVU updating, does one really need to wait 3 to 6 minutes for a good accuracy update? Thank you.

Thanks much for that, will give that a try. Good that the system knows to continuously track the spatial positioning even with the image frozen / stored.