Nahemoth

Hi, I have been "out" for a while... and I see this DLSS4 discussion, which seems a bit confusing... using the latest NVIDIA driver, do we need to replace the DLL file in DCS or any other game? Or just change the settings in the NVIDIA inspector? Thanks!

I have read that thread and it is clear that something has changed...

Thanks!

I found that while defeating MANPADs using flares is feasible, evading the IR missiles launched during a dogfight is nearly impossible for me. I do what it is supposed to be done: engine idle/mil, launch burst of flares and pull-g's to evade IR missile. I have plenty of tacview records, where I see that the flares are not working properly, the IR missile does not lose the target and it goes directly to me. Any advice? Thanks! Here are some tacview screenshoots (I may share the tacview files as well): null null

Hi, I'm selling the Pimax Crystal OG (Original) VR headset, which I received in July 2023. It includes a PCIe card for USB 3.0 (StarTech PEXUSB3S42V). I may ship it to the EU, preferably to Spain. The price is 1100€ + shipment cost. Let me know if you have any questions. Thanks

Are you using the default settings?

Thank you!

Hi, Do you have any recommendations for a good JTAC mission? Thanks!

I wasn't aware of that, but after reading your post, I started noticing the small vibration in DCS, with the Crystal and LH faceplate. I don´t know if this behaviour can be seen outside DCS.

Do you mean inside DCS? Or in the HOTAS software configuration?

Good trick

Having an 8kx, I will receive the Crystal in less than 2 weeks, I'm curious about how small or large is the FOV, depending on the review, it is very small, or it is enough... so relative. But in my case, my IPD is too low, and setting up the 8kx was terrible, the image is always blurred... so let´s see with the new glasses.

Hi, Is there any keybind for engaging barometric attitude autopilot mode? Instead of using the UFC, with the HOTAS. Thanks

Still available

Thank you very much for reminding me, I forgot to highlight that!

Hi, I'm selling my Pimax 8K X KDMAS version, it is the model that can be configured at 60 Hz refresh rate, for those that can tolerate it. I'm based in Spain, but I can send it to Europe. I sell it for 650 euros + shipping Some pictures attached. NOTE: The PointCTRL unit is not included, I will remove it before sending. Thanks nu

My IPD is low (57), that's why I'm asking. Concerning the FOV, I'm afraid of that... I love large FOV. I read there some new lenses for increasing the FOV, but probably the clarity will decrease, at the end it's a trade off....

I have just received the payment email (preordered on April) but I have plenty of questions... what about FOV and IPD? I own a 8kx, the IPD has been a bit tricky, but the FOV is fantastic... any advice? Thanks

I was thinking on starting with the Viper (after completing several Hornet campaigns), but seeing the good comments about the F-15E module... what would you recommend right now? F-16C or F-15E?

I tried your setup, you need a really strong arm

I tried it again, and I don't know what I did yesterday, but now it runs as expected. The OXRTK FPS counter shows coherent frametimes, and most of the time I run at 90 FPS. Not sure yet if I get any benefit from running at 90 Hz compared to 60 Hz, need to do more tests, but what is the adverse effect that people feels? I also run at normal FOV, wide FOV decreases the clarity, so for me, the normal FOV is a very good trade-off.

Hi, I'm used to set the Pimax 8kx at 60 Hz, getting good performance at high settings without MR (even with SteamVR and MSAA x2), but I wanted to try your 90 Hz settings with OpenXR (FFR and CAS), as the experience could be even better. The performance results were not the expected, I hardly maintain 90 FPS (instant action missions), and the DCS FPS counter says I was "CPU BOUNDED", which is strange considering that I run the MT version. I tried to see the CPU/GPU frametimes in DCS FPS counter, but no success, maybe I should try the ones provided by openxr toolkit. In any case, I need to research the issue of "CPU BOUNDED", any tip? Maybe something related with the selected E-core and P-core? BTW, my rig is composed of a 13900K (@5.6 GHz) and 4090 (slightly overclocked) Thanks

I think that I will stay in MT version with SteamVR, I will do some performance tests for comparing results.

And why not going back SteamVR? At least until these problems are solved...

Yesterday I noticed this same effect after switching back from the map view. But after exiting the mission and entering again in another one, it recovered from the previous bad behaviour.