All Activity

Hey Hedgehog, it happens. These tiny aircraft names on the forum can get confusing for anyone, especially their being so similar. Sorry for assuming it was for Flaming Cliffs, its been ages I haven't visited the Eagle on that module. This could possibly be an accidental mouse wheel action when the cursor is coincidentally over the lever in game. Very hard to tell from this perspective. I've flow with this bird the most and that never happened, in other hand a few of little accidents with mouse being in an unfortunate place and a click or scroll is made unknowingly. If it happens again, a track would be the most valuable tool to figure it out.

Благодарю, наоборот выключил через Альт+Q и носовое колесо встало прямо, не криво

The ATZ-60 tractor can't connect to a trailer. Yeah, yeah, I know. The ATZ-60 is a refueling truck cab, right? but it cannot be denied that it is a tractor. There is an action to connect a trailer in the waypoint editing type, but I have tried all units and cannot select the trailer unit. I wonder if this tractor is just for show? Tell me?

Make sure you are within the min and max limits. Use the red and green circles to see where they are. Also make sure you are deployed on a flat surface.

Here's a new behavior... Suddenly get a gear warning in flight... Winwing PTO panel red lollipop flashing and gear alarm sounding, still in the retracted position. I look in the cockpit and the gear handle is in the 90-degree rotated Emergency Extend position. And gear is indeed extended. I checked control bindings. I have absolutely nothing... no keystrokes, nothing... bound to any of the Gear Emergency Extend or Retract commands. The only way to possibly command this would be to point the mouse cursor at the gear handle and roll the mouse wheel, which I did NOT do. What else could possibly cause this behavior?

Yeah, sorry, initially posted in the wrong area somehow. This is about F/A-18C Hornet.

Hi, first of all thanks for the new units, it was very much needed to get some modern weapons I can't get the Iskander to fire at a point or at a unit/group. What are the min and max launch ranges and are there more things that would prevent it to fire?

I want so badly to love the Corsair. I DO love the Corsair. But I can't fly it since the last update! Can't taxi to the runway, same as others have described. I can take off and land on the CV since there's no taxi turning involved. The supposed 'experts' telling us how to use the pedals/brakes are clueless. I defy ANYONE to go to Instant Action, Nellis, Cold Start, then start up the plane and taxi a 360 degree circle. Can't, can you!

Are the FM1_FREQ and FM2_FREQ still valid? My triggers don't fire using them.

this issue has been reported thank you

thank you for your post, this has been reported

Always check all displays. Or...... Five miles to my airfield. I check all important indicators and prepare for landing. Everything looks good and I think I have the changes to the flight model under control. Suddenly the engine sputters and stops. What the f... is that? After a few seconds I discover my mistake. Ignored the fuel gauge. I'm simply out of gas.

On the other hand, I also noticed that since the last update 2.9.19.13478/ I have micro freezes again and the image jerks when I turn left or right quickly, which had disappeared with the previous update

Hi, please attach your dcs log, we can look for clues. thank you

Hello, after reading what Hot Dog said, I took a flight just to look in the fields, and the combine harvesters have disappeared too. !!

Почти похожий на dcs-совский.

@Wags Thank you for explaining why there is a delay in getting the new soldier models out there on the "Mover and Gonky" show (loved seeing you on the show by the way) These are something that I have been asking for recently and getting frustrated due to the lack of release when they seem to be ready from all the promotional videos.

Could it be a better headset than quest pro now? Sorry for offtopic I am planning upgrade from quest2. Only minimum of 90Hz troubles me. For my configuration it's now fine and stable on 72Hz.

Hi, here I am again. I changed my PC configuration as best I could. Hoping to improve performance, I reinstalled everything, but now it's getting to the end of the loading process and crashing! I'll try to send the log. Thanks in advance for your help. Regards Gaetano dcs.log dcs.log-20250819-102030.zip dcs.log-20250819-102342.zip

With the recent update the Bullseye data when enabled shows up fuzzy on the FCR and clear on the HSD. I noticed the same condition when swapping the FCR from left to the right MFD.

Imho sorely needed even if it has to come as an FC3 level module due to lack of documentation.

Thanks! I’ve read some Reddit posts saying the clarity or sweet spot is significantly lower than the Quest 3, which doesn’t really match what the publicity claims. How do you find it compared to the Q3 in terms of sweet spot and overall performance (especially running DCS and iRacing)? Have you also tried Virtual Desktop with the Q3, and if so, how does the BSB2E stack up in smoothness and clarity? Also curious if you notice any optical distortions around the edges, or if the image feels more consistent than on the Quest 3/Pimax.

Yes, this is expected behavior given his current implementation. You need to disable him first if you want to mess with that stuff in particular (Wheel > Presence > Disable, can also be bound to a key directly). Once the vision for Jester fully unfolds and everything is in place, these things should not be a problem anymore Are you sure about the elevation though? In all user supplied tracks ive seen on the topic so far, the elevation was usually good and did cover the airspace with the bandit in (he runs a sophisticated default scan pattern that touches pretty much the entire airspace ahead). The problem leading to not spotting the bandit on the screen is usually the gain, not the elevation. Either case, as a default uninformed scan behavior I think its quite good already. It just lacks, as explained earlier, an extra mode where he actively tries to uncover a target in a known area.

I've had mine (BSB2E} for a week now. Got it pretty well dialled in for DCS and Iracing. Coming from A G2 running 13700K/4090. Happy to answer any questions.

We have a report open, but it is a long standing issue. I have bumped the report internally, but I have no other news to share sorry.