Bucic

@edup71I was referring to cockpit textures. Haven't seen external shots of the FC24 '5.

@Doughguy Thanks for giving it a try. Would you be willing to share the current version of the damage textures as a WIP? I seriously doubt it's going to look worse than the stock ones.

Well, if you go for either the weapons panel or the fuel systems panel, those are quite easy to pull off. The 3D printed stick is available so in my eyes the throttle qdrt is the biggest challange. If you have any questions or thoughts, do chime in the linked simpit topic. Not a word from me about the simpit in this thread, I promise

And that's what skill-based gameplay is. Many of us do not play multiple stat-based genres for a reason.

Not only it's the old textures, it's even the old set without fixes. https://www.digitalcombatsimulator.com/en/files/3305829/ Back to tuning my drill press...

Same here. Also with F-5E being one of the most dad-friendly modules I can't imagine what you'd simplify further.

Is the F-5E going to have better cockpit and external 3D models than the standard FF DCS F-5E module?

Longshot and B4ME might be good dogfighters but I have never seen anyone else ride the '5 like this guy! Probably a RL pilot as well. https://www.youtube.com/@murdok123/videos

With each new wacko there is always a hope to bring another poor soul into F-5E simpit building

Start here + find the Bunyap's walkaround video Tutorial library channel - DCS F-5E Tiger #1 - Aircraft General - https://youtube.com/watch?v=JibCd3fpc2U Proper basics Tricker DCS F-5 Enroute Tutorial - https://youtube.com/watch?v=GKgDm1PqChE RL RAF pilot instructor Tim Davies Master F-5 Circuits Like a Pro: Expert Tips from a Real RAF Flying Instr... - Comedic Shortcuts by Laobi 1 Minute DCS - F5 E Air to Air MSL Mode Tutorial - https://youtube.com/watch?v=I18lrOg_AGA TACTICS COMPREHENSIVELY! Ops centre by Mike Solyom MP dogfighting - learn by watching Bullet4MyEnemy F-5E Tiger II - Mastery: Part 1 || DCS World - https://youtube.com/watch?v=CRahJaD1lXk Phoenix 3 How to Cold Start and Fly F-5E Tiger II DCS - https://youtube.com/watch?v=x9fj5XMD30g

Darn it! I guess I won't be doing any simpit work once you release it Quick question. What resolution might be the stock P-47D textures? They look closer in terms of quality to your textures than to what we have as stock textures for Dora.

Same here after the update. Grab short track files gents! https://forum.dcs.world/topic/320363-engine-issues-when-using-mw-50bug/?do=findComment&comment=5415389 The real deal RL manual for the Jump engine in this post

I've been flying the same mission over and over for the past month. At least before the main April update. IA - Thunderbolt furball. Always the same way: 1. 0-1000 m 2. 350-450 km/h mostly 3. yankinkg the throttle (Xbox controller) 4. not touching the radiator flaps knob 5. MW50 used CONTINUOUSLY, sometimes over 5 minutes at full throttle without a single retarding of the throttle. Before update: No engine failures without battle damage. After the April update: I started getting unexpected engine failures. I think they are preceded with a pop sound. I'm going to try to grab a short track file.

Thanks for chiming in! That was what I suspected but wanted to make sure I'm not missing something obvious.

I'm going to try this out: Also found anothr thread. Recent bug being hunted down More findings Even more I guess a shoddy manual does translate into higher post count.

You revert back by the feel of your physical controls. I think I can only only achieve that by diving down in the cockpit. Just stating the obvious

I agree. I'm only asking for the purpose of combat emergency where the engine starts to misbehave right after I take hits. I'd crank them open, climb, heading home and only then I would like to slowly "get back to auto" and observe the engine parameters. That non-feathering propeller is a bummer since dora has a high aspect ratio wings and would glide pretty far. So it would seem the knob doesn't command the position but rather the thermostat setting. So: fully closed position is 1000 deg Celsius fully open is [still around 100 deg Celsius with flaps automatically closing to whatever position gives 100 deg Celsius] How about the takeoff procedure? Am I dreaming this up? There was never anything about radiator flaps in the DCS takeoff procedure?

The manual only mentions the manual mode for the automatic governor failure. It's hardly a complete discussion of the subject, not to mention it's hard to say if the governor is fine after taking a spray of 50 cal on the whole aircraft. Any tips? I usually leave the MW50 on and decrease RPM, cowl fully open manually.

How it's done? There's no "back to auto" keyboard binding in-game. Also, wasn't "cowl flaps manually fully open" part of the Take Off procedure around 2015?

The recent February audio overhaul is already a huge deal. It's now more fun to taxi on the runway than to fly the Dora pre-update An update to the 3D model, 3D damage model and systems damage modeling would have been great. The Yo-Yo's landing gear physics overhaul is destined for all the aircraft so it's only logical Dora gets it pretty soon. P-51D Mustang | Testing the new landing gear physics update | DCS 2.9.4 - YouTube —

I'm going to use the Package Editor, sorry for bothering you. I'm using the mod as a regular non-zipped folder for now.

I've just tested with Nanazip (a 7zip clone in MS Store) - .zip - LZMA2. OMM picks up the mod using the "Add mod" [+] and the archive gets added to the hub Library folder but the mod is not visible in the interface mod list. bloom kill mod by Bucic feat LucShep OMM compat.zip

I think people don't realise what the updated landing gear physics mean, per the P-47 mention in the changelog. It's the beginning of the Yo-Yo's ldg modeling project that in the future is going to be implemented further module by module. So eventually even godforsaken modules like F-5E may receive it.

wut?! 300 EUR is quite feasible even for me. There's a lot of missing info though. 1. How many motors/channels does the controller support? 2. What are the differences between the DIY kits? I am guessing I'm supposed to conduct comparison of the motor specifications myself. 3. Do you have a discount you could share, as the brand ambassador?