dukovac

Thank you for your answers. Blink of an eye for my lightning fast 30 Mbit/s connection.

Can someone please tell me is this normal?

Please include more control options for switches and add axis for lights, Yaw Trim etc. One example for comparison, HORNET module has 7 options for one switch: FLIR Switch-Down FLIR Switch-Off FLIR Switch-On FLIR Switch-STBY FLIR Switch-Up and most important FLIR Switch-OFF\STBY FLIR Switch-ON\STBY The A10c Master switch has only 3 not very useful options: Master switch ARM Master switch TRAIN Master switch SAFE It would be better to have "Master switch ARM\SAFE" and "Master switch TRAIN\SAFE" A10C II Tank Killer module is a real masterpiece, but control options are well below the level set by the person who created controls for HORNET.

Have a look

I don't believe this is possible. Your resolution is larger than you main monitor. Try to make a screenshot of your desktop and paste it into "Paint" or something and you will get the same result. Maybe there is some "third party program" that can capture specific areas of extended desktop. DCS sees the upper left corner of your #2 monitor as a starting point for x, y. The simple solution would be to manually enter the combined resolution of #1 and #3 monitor into DCS options and move monitor #2 to right side and re-adjust coordinates in lua.

Hi! This is my setup with six Dayton Audio TT25-8 PUCK 8 Ohm transducers and 3 cheap amplifiers.

I'm using Helios only to create additional viewports after every DCS update. I found better screen, but it's expensive. https://www.waveshare.com/3.5inch-hdmi-lcd.htm

You can use USBDeview to quickly navigate through your USB controllers and for renaming check this tutorial https://www.isrtv.com/forums/topic/25278-how-to-rename-peripherals/ You are just postponing your inevitable transition to Arduino:)

@crash test pilot https://www.ebay.com/itm/3-5-in-Display-Panel-Resistance-Touch-Support-HDMI-Audio-Output-MPI3508-480x320/323981976872 Nice work with the pit! I have incomplete right side built into an Ikea Lack tv bench. Hornet-a10c hybrid. I'm planning to dismantle everything and build full a10c pit

Are you planning to add 3.5" display to CDU? I bought a TFT display and is very difficult to read anything unless you are watching directly from above.

Prototype circuit board from local electronic store

2.5.6.60645 Open Beta(jan 27) ,but you need to create folders yourself.

Hi! I have static.ogg in saved games folder and its working. C:\Users\YourName\Saved Games\DCS\Sounds\Effects\Aircrafts\Cockpits

Very true! I unfortunately own several virpil products and had mechanical problems with almost everything except for desk mounts. Some examples: button caps falling off from throttle and stick, useless detent on right throttle, the uneven force required to go from side to side on the same axis on the CM2 base, Warbrd 5pin din cable breaking ... Had a streak of bad luck with virpil and now I see their products as unreliable, overpriced and of unpredictable quality.

Full hotas setup from Virpil (MongoosT-50CM2 Grip, WarBrd base, and MongoosT-50CM3 Throttle) is 877€ with cheapest shipping and VAT included. That's really terrible and greedy. Warthog price is at least 300€ lower.

I'm sorry to hear that. In the third column (Calibration) you have "Type: with center". I would make it without center. Do that and then move mini stick to left, hold it there and press start, move it to right, hold it there and press stop. Skip the center. Do that for both axis of mini stick and set all dead zones to 0, including dynamic dead zone. If that doesn't work, you better try your luck on the virpil forum because I'm out of ideas. After you make changes don't forget to click first on blue "save" button and then on green "save VPC device".

Thank you Nikolas_A! At least now I know where to start looking.

I have some old motor that was used in the simulator. Anyone know is it possible to connect it to the Arduino and DCS bios?

Min - The deadzone value % of the lower end of the axis input. Center - The deadzone value % of the center of the axis input. Max - The deadzone value % of the upper end of the axis input. Dynamic - A dynamic deadzone % that operates throughout the entire range of the axis input as a 1/10th % (value “5” = 0.5%, or “15” = 1.5%) of the last polled value. Similar effect to the smoothing value for removing jitter but without obscuring or slowing the polled input response. https://support.virpil.com/en/support/solutions/articles/47001121642-vpc-software-technical-overview Try with Middle 0. If axis begin to drift on its own increase to 1 etc.

I am not sure. Maybe here you can find a tutorial.

You are getting to much travel before it starts to move regardless of axis settings in DCS? If that's correct, then mini-stick probably has dead-zone which you can reduce in the Virpil configuration tool.

What kind of sorcery is this? I don't have VR or RTX series card, but I followed your guide to some extent and results are amazing!! Thank you, I owe you a beer!