darkman222 Posted November 15, 2020 Posted November 15, 2020 See the image attached. When I have Aim 9Ms loaded, I can see the target closure rate in my JHMCS and the dynamic launch zone. When I fired all my missiles the DLC disappears, which makes sense, but the target closure rate display also disappears. Which is annoying, because now I have to check closure in the HUD display, taking my eyes off the target. That is really bad, when I am out of missiles and now in a guns only fight, at that point. Is this behavior realistic for a block 50? Or is it a bug?
llOPPOTATOll Posted November 16, 2020 Posted November 16, 2020 The bracket your pointing to is the DLZ so once your out of missiles there is no DLZ because you dont have any weapons left.
darkman222 Posted November 16, 2020 Author Posted November 16, 2020 Yes, sure. The DLZ will disappear. I should have drawn the arrow from the left side or a circle around the number. The numbers representing the closure rate also disappear, which makes no sense to me, as in a guns fight closure is even more important. This is why I am asking if its realistic or not. I drew a circle to make sure you see the number I am talking about.
Csgo GE oh yeah Posted November 22, 2020 Posted November 22, 2020 Time to active and Time to impact also disappear from the HUD after last missile 1
darkman222 Posted November 23, 2020 Author Posted November 23, 2020 Yes I understand. But why does closure rate disappear too. It does not make sense, as it is very relevant in a guns only dogfight when I dont want to overshoot. With no missiles left, only guns, I have to take my eyes off the bandit to check the tiny closure rate display in the HUD now, instead of the well readable one in the JHMCS. My question is, if it is a bug or a realistic behavior of the block 50.
Emmy Posted November 23, 2020 Posted November 23, 2020 While it should probably be in the HMCS, you do have closure rate on your HUD (769) just below the distance read out in the lower right corner. [sIGPIC][/sIGPIC] http://www.476vfightergroup.com/content.php High Quality Aviation Photography For Personal Enjoyment And Editorial Use. www.crosswindimages.com
darkman222 Posted November 23, 2020 Author Posted November 23, 2020 Yes thats what I mean. Now I have to look in the HUD on those tiny numbers. The closure rate calculations are done by the aircraft and not the missile. So, why would closure rate disappear from the JHMCS then, while it is still displayed in the HUD?
Csgo GE oh yeah Posted November 26, 2020 Posted November 26, 2020 What i meant was, i can not see when my last fired missiles goes active . The time to active just disappears, which is weird if you still have a missile in the air right ?
darkman222 Posted November 29, 2020 Author Posted November 29, 2020 Now I get it. That might be related to what I was already thinking about the closure rate symbology disappearing. That could be a hint that it is a bug and the symbology in that area gets disabled with the last missile fired, instead of being displayed with or without missiles anyway. The issue could be bug report worthy.
USA_Recon Posted November 29, 2020 Posted November 29, 2020 Wish aspect angle (as shown in radar) was in the HUD as well - guess it wasn't irl ?
USA_Recon Posted November 29, 2020 Posted November 29, 2020 What i meant was, i can not see when my last fired missiles goes active . The time to active just disappears, which is weird if you still have a missile in the air right ? I have noticed this as well - TTA should not disappears
dorianR666 Posted November 29, 2020 Posted November 29, 2020 yes its a bug CPU: AMD Ryzen 5 1600X GPU: AMD RX 580
Recommended Posts