correct as is Rudder trim off sometimes trims rudder

[jmijnen]

This one sounds wack, but I seem to be able to get my rudder to center off-center (as if it is trimmed) while my rudder trim is off. Resetting my trim will properly center it again.

[BIGNEWY]

Hi

 

please include a short track replay, all seems ok here

 

thanks

[pirilampomagico]

me too same problem. the left pedal is down even i not touch it

Edited June 16, 2021 by pirilampomagico

[H0RN3T]

yes, you are probably using YAW autopilot (autopilot h channel) , thats why 

Edited June 16, 2021 by H0RN3T

[NineLine]

3 minutes ago, H0RN3T said:

yes, you are probably using YAW autopilot (autopilot h channel) , thats why 

 

Yes, please check this, thanks!

[pirilampomagico]

i will check that thank you

 

3333.trk

[pirilampomagico]

i did check and my autopilot is off i think another reason is doing that

it has never hapen with any module i own

 

Edited June 16, 2021 by pirilampomagico

[NineLine]

Did you change anything in the special Tab? Like the Rudder Trimmer option?

I will check the track shortly. 

 

Thanks!

[ArjenHVA]

Also having this issue. Reset rudder trim is the solution (LCtrl + T) but it starts with an offset. Special tab settings. 

mi-24 rudder.trk

[Soulres]

I get this too,and I dont even use the trimmer.

[pirilampomagico]

31 minutes ago, NineLine said:

Did you change anything in the special Tab? Like the Rudder Trimmer option?

I will check the track shortly. 

 

Thanks!

No i didnt change noyhing there

[Soulres]

Its cause of teh auto pilot Rudder. I was lead footing my pedals and the Rudder-Autopilot corrected almost the entire LENGTH, and VERY slowly crept back until I reset with LCTRL - T and it fixed itself

 

I belive this is cause the Rudder Trim Speed for the auto pilot is slow.

[NineLine]

Thanks for the tracks guys, looking now. As something to try, Wags suggested adding a deadzone if you dont have one. But I am looking at the tracks now, thanks!

[pirilampomagico]

40 minutes ago, ArjenHVA said:

Also having this issue. Reset rudder trim is the solution (LCtrl + T) but it starts with an offset. Special tab settings. 

mi-24 rudder.trk 2.1 MB · 0 downloads

Ok thank you i followed your advise and works well. Probably the real aircraft at real life also have such atitude so well just recenter rudder at starting fly and aparentely all goes good

 

[NineLine]

Hey guys what are you using to control your rudder. I see with the keyboard you can set it one way or the other and it stays, but with rudder pedals, with springs, its fine, snaps back to where I would expect.

[ArjenHVA]

1 minute ago, NineLine said:

Hey guys what are you using to control your rudder. I see with the keyboard you can set it one way or the other and it stays, but with rudder pedals, with springs, its fine, snaps back to where I would expect.

T.16000M RZ axis assigned to Flight Control Rudder. For me the one time action of the rudder reset worked because every subsequent flight I started, the rudder was centered from the start.

[NineLine]

Ok, this is correct as is. The aircraft starts trimmed so that when you release active pause you don't go spiraling to your death. As noted above, the way to re-trim if you choose is to reset the trim.

[robin00795]

Im having a problem , when I trim the chopper the trim seems off , and sometime trim way to much on the left , using a sidewinder force feedback 2 

[NineLine]

Will need a track, sounds different than this report.

[pirilampomagico]

Ok thanks Nineline.

[robin00795]

13 minutes ago, NineLine said:

Will need a track, sounds different than this report.

track trim problem .trk

[yngvef]

The Yaw autopilot did indeed cause some confusion for me the first time. And it seems that if it gives a huge control input to one side and then you turn it off while the input is at max, it will stay there until you reset trimmer (even with rudder trimmer disabled in special settings)

[robin00795]

fixed my problem , needed to invert axis in ffb

[MAXsenna]

fixed my problem , needed to invert axis in ffb

I had to swap them too.
First module I had to invert them though!

Sent from my MAR-LX1A using Tapatalk