Olliecast Posted March 1 Posted March 1 9 hours ago, PLUTON said: Here I installed DLSS 3.10.2.1 and set the preset to K in Nvidia inspector I did a flight test on several cards and the result is a minimum loss between 10 and 15 FPS in VR (that's a lot I think) Am I the only one with this loss of FPS? Tank you for help It’s interesting you say this. preset k looks better than standard but I’ve been struggling maintaining fps - with my og crystal, quadviews and a 4090. I’ve changed to the latest nvidia driver this morning and initial tests seem a bit better. anyone else seen Peformance loss?
PLUTON Posted March 1 Posted March 1 Since my last message I also switched to the latest nvidia driver and the loss of fps is much reduced now the difference is 5fps but dcs remains fluid despite that. But I will do other tests to know if I keep the K setting or if I switch to G as some have said that their config ran better with G or F rather than with K.
PLUTON Posted March 2 Posted March 2 Here I did some tests in VR with the preset set to J and K and I did not notice anything that could make the difference between the two except maybe the preset K a little sharper and I am not entirely sure. But whether it is one or the other I noticed a clear improvement compared to before (DLSS 3.8.) . With the (DLSS 3.10.2.1) and the J or K setting in Nvidia Inspector I have Just lost a few FPS but DCS remains fluid and the sharpness has been greatly improved. 1
greyeagle787 Posted March 19 Posted March 19 Thanks for all the info here. I am using Tweaks and the DLSS Swapper for DCS. One issue I’ve had is the settings don’t stay where I set them. I updated to the latest DLSS Swap and used “J” in Tweaks. Worked fine but the next time I checked in DCS it reverted to the 3.7 and C settings. How do I keep these settings permanent?
sleighzy Posted March 20 Author Posted March 20 1 hour ago, greyeagle787 said: Thanks for all the info here. I am using Tweaks and the DLSS Swapper for DCS. One issue I’ve had is the settings don’t stay where I set them. I updated to the latest DLSS Swap and used “J” in Tweaks. Worked fine but the next time I checked in DCS it reverted to the 3.7 and C settings. How do I keep these settings permanent? Did you update your DCS today? It will replace the dll files with the original ones and you need to replace them again. ...if that was the case for you. AMD 7800x3D, 4080Super, 64Gb DDR5 RAM, 4Tb NVMe M.2, Quest 2
greyeagle787 Posted March 20 Posted March 20 2 hours ago, sleighzy said: Did you update your DCS today? It will replace the dll files with the original ones and you need to replace them again. ...if that was the case for you. That must have been it. So if I get this right I have to re-Swap back to 3.10? Will my tweaks setup remain the same? (Still trying to get how this works) Thanks
sleighzy Posted March 20 Author Posted March 20 Just now, greyeagle787 said: That must have been it. So if I get this right I have to re-Swap back to 3.10? Will my tweaks setup remain the same? (Still trying to get how this works) Thanks Yup, all your settings will remain. Just need to put back the new DLSS4 310.x.x. dll again that has those fancy presets. AMD 7800x3D, 4080Super, 64Gb DDR5 RAM, 4Tb NVMe M.2, Quest 2
greyeagle787 Posted March 20 Posted March 20 1 minute ago, sleighzy said: Yup, all your settings will remain. Just need to put back the new DLSS4 310.x.x. dll again that has those fancy presets.
Recommended Posts