TaliG

This is happening already with the new ''edge'' maps. Those maps will be payware..

First pass above runway, stability control (s) is on. Check rudder deflection when I roll left and right. (no rudder input) Second pass, stability control (s) is off. Here you can clearly see the rudders deflect left and right while i only give roll input. (no rudder input) please look the track i uploaded on the thread below... http://forums.eagle.ru/showthread.php?t=133410&page=5

No need for track file i suppose..

Rudders directly connected with ailerons (roll axes) bug. First pass above runway, stability control (s) is on. Check rudder deflection when I roll left and right. Second pass, stability control (s) is off. Here you can clearly see the rudders deflect left and right while i only give roll input. rudders directly connected to ailerons.trk

take a look. I started on air near Maykop, landed and took off again. nothing touched on the editor just add the plane and hit fly (summer +20, 56% fuel). Try to get my numbers (nose up speed 230 and take off speed 250) when you load the mission from the ground. Not possible. takeoff spd after landing.trk

1. Airspeed acceleration - deceleration arrow on hud does not work. 2. Barometric and radar altitude hold mode adds opposite trim on the roll axis (FFB joystick) when you try to make a turn. Trimer on normal flight, Route following mode and altitude + roll hold mode works fine. (i did not test the other AP modes) 3. Auto rudder stabilization needs a lot of tuning, especially for speeds below 400kph. When you bank from one side to another, it always ''overcompensate''. Even the autopilot on route mode on landing cannot cope with it and starts to heavily oscillate the nose left and right on the y axis. It flies fine if you apply full opposite rudder (when at landing speeds). At speeds above 600kph this behavior is unnoticed. 4. The flight model is heavily bugged when starting the mission from the ground (ramp start or taking off from runway) Eg: Not possible to lift the nose on takeoff while airspeed is below 300kph less than 10% fuel onboard. Flaps up-down and or trimming makes no difference on nose lift speed. BUT!!! When you load the mission in the air, leave your controls untouched for 3-4 secs. Fly normal and go land.. Now try to take off... VUALA!!! nose lifts up at 250-260 max even with 90% fuel and weapons onboard!! Overall, I am very impressed with this pfm. :joystick: Great work ED!! :notworthy:

Can you hear your doorbell? :D If you dont, then be prepared to also ''FEEL'' the :police: dragging out of your cockpit and transporting you to the nearest police station.. :doh: ( the sound of the police breaking your door will easily blend with the battle sounds, so no chance of hearing it either :D )

:D

Looks like system ram or gfx memory corruption. A game restart solved the problem I suppose..

SU-34

Im happy you took off mate, im sure others in this forum are happy as well..You know.. here we can even join our ''foot power'' and PUSH (literally) your aircraft down the runway in order for you to take off ;) I wish you safe flights my mate!

cmon mate...they know that the overhead panel from the huey is UNFINISHED. They Know about al the unfinished staff... What bothers me is not he unfinished stuff, .. it is the luck of communication towards the community. thats all. EDIT: together with the mi8 manual EDIT2: ok no more rage lets get a drink and wait the outcome...I know its going to be a perfect sim in the end...but sometimes you know...we get drown in the alcohol...

This is wrong, and you know it... (we paid for it) dnt ask for help to finish your ''already paid product'' from your customers... EDIT: dnt get me wrong ...but you paid modders start to ask more than you provide..

nok nok ...no one is there..

Nice pics! :beer:

What is the speed of your new ram (Mhz) when running at 7.7.7.20 1T latencies? Those are very nice latencies you achieve there mate :thumbup: Are they stable ?

Hi Cibit, stick with 1600mhz (which by the way, is already too high for your cpu's mem controller to handle), and choose modules with the lowest latency (CL) at the lowest operating voltage. Performance (fps) will be ''nearly'' unnoticeable with higher speed mem anyway. Also it will be quite difficult to keep your 3.7ghz cpu OC if you run mem modules on higher speeds than your current mem is running. best regards :beer:

Sorry, previews picture for connecting the modules was wrong :blush: this is the ''recommended'' way... Anyway, if u disable dual channel support from inside the bios I think u will be fine...

Yes , Skate is right. This is the main reason why manufacturers sale dual and quad channel mem kits. Those kits are tested and certified to work dual or quad channel. But if u disable dual channel support they all work perfectly well. I dnt know the exact impact on game performance though..

Hi Devrim! Pls follow these steps... 1. Disconnect the power button cable from the mobo and start the PC by shorting the pins with a metal object. (believe me I ve seen power and reset buttons fail, and they are a pain in the but to figure out if u dnt check them from the beginning) If no deference, reconnect. 2. Test avry memory slot by connecting only one module at a time to each one of the slots. (always drain the remaining current from the psu before you do this) If all slots are fine (PC boots with only one module inserted in all of the slots) your mobo is ok (slots have no broken traces) 3. Insert modules like in the picture below if u didnt already... : 4. If u still have problem, then boot with 1 module into the bios, and disable ''dual channel mem support'', then insert all modules and reboot.

A hint from a thread where they were talking about controlling F15s new AFM pitch with keyboard... So I think the it is already in beta testing :smilewink: EDIT: Thread is here : http://forums.eagle.ru/showthread.php?t=128346

Eat lots of beans and try again .. :D

As a tomcat owner (not f14 :D) I would recommend you to teach your cats to not chew on cables. To do that, use a plant sprayer and spray their forehead with water whenever they start chewing. They will eventually stop doing it. Use this method for everything else you dnt want them to do. :smilewink: Good luck!

can u be more clear about your problem? is it an activation problem or a crash problem. This is a crush thread if im not mistaken. please be more specific in order to get help. all modules plus MP works fine at the moment...v129

fc3, a10c, mi8 and huey runs fine on my system. Can you please install a fresh dcs world 129 and then your modules? also check your hdds or ssds for bad sectors (hdd) or ''tired' memory (ssd). EDIT: I do not have the sabre installed, only updated to 129