AV8 3d printed nozzle lever for warthog throttle

[FoxDelta]

That looks great FoxDelta, very nicely done!!

 

THX, and it remains in position like built as one piece thx to your connection solution:)

[FoxDelta]

download avbl

 

DOWNLOAD online , check 2nd post

[FoxDelta]

added a short video

[Ala12Rv-Tundra]

DOWNLOAD online , check 2nd post

thank you, looking forward to this project

[Fusedspine33]

Thanks again Fox

[FoxDelta]

u r welcome

[FoxDelta]

just for the optic

[Fusedspine33]

What did you use for the brush

[FoxDelta]

its called STORMGUARD, its used at doors to prevent air from passing below. u can buy it in every doityourself shop, i trimmed it in length, width and density. and bent it to fit, its cut a bit too long to remain there by itself

 

https://www.amazon.co.uk/STORMGUARD-02SR0200914W-Bottom-Draught-Excluder/dp/B002Q0ZB9M/ref=mp_s_a_1_5?ie=UTF8&qid=1553183184&sr=1-5&refinements=p_4%3ASTORMGUARD&pi=AC_SX236_SY340_FMwebp_QL65&dpPl=1&dpID=31vyp2dCPGL&ref=plSrch

Edited March 21, 2019 by FoxDelta

[Ala12Rv-Tundra]

looks epic

[Bipper]

:thumbup: Awesome. If/when you're looking for your next project, do a wing-sweep handle for the F-14.

[FoxDelta]

:thumbup: Awesome. If/when you're looking for your next project, do a wing-sweep handle for the F-14.

 

just flew the f14 for a few carrier pattern ( the kneeboard sheet for the grade is awesome , should be done for the f18 as well), but would u really need a sweep handle? (isn t it 99% operated in auto mode? the handle itself can be done easily by modifying the AV8 project, to make it motor driven i may do some investigation wether the module supports output of the sweep angle or not.

when i flew it i would have preferred to have a flaps handle

Edited March 23, 2019 by FoxDelta

[Ala12Rv-Tundra]

ey mate, did you add some stuff to the Warthog throttle to improve the grip?

[FoxDelta]

ey mate, did you add some stuff to the Warthog throttle to improve the grip?

 

yup, someone mentioned this grip sheets here in the forum long time ago and, because my warthog became old and ugly i went for it, the rubber version (i used on this photo ) is more for the look than to add more grip, the granulate adds grip but is not as stylish, see yourself here

 

https://talongungrips.com/other-grips/material/large-sheet-5x7.html

[VooDoo-S8]

Hi mate,

 

Awesome job! Just had a look at the files.. what's the part that connects the nozzle lever to the warthog throttle called?

 

As soon as I go from 'looking' to 'printing' I'll send some beer/filament money your way!

 

Cheers,

 

Voodoo

[FoxDelta]

Hi mate,

 

Awesome job! Just had a look at the files.. what's the part that connects the nozzle lever to the warthog throttle called?

 

As soon as I go from 'looking' to 'printing' I'll send some beer/filament money your way!

 

Cheers,

 

Voodoo

 

i guess u re looking for the base_connector, u will need the base distancers as well to avoid wobbling

 

glad u like it, tell me your suggestions when you went to printing

Edited April 6, 2019 by FoxDelta

[Marcq]

Awesome work :thumbup:

 

Marc..

[VooDoo-S8]

i guess u re looking for the base_connector, u will need the base distancers as well to avoid wobbling

 

glad u like it, tell me your suggestions when you went to printing

 

I don't think I'll get a chance to print anything until next week but it looks awesome!

 

I think the part I'm looking for is the "lever_taker"? There is a gcode file but not an .stl that I can load in Cura.

 

Again, Awesome work man!

 

VooDoo

[VooDoo-S8]

This part here mate..

[FoxDelta]

This part here mate..

 

u re right , looks its .stl is missing, added in a minute

 

UPDATED the nozzle_lever for better bendabillity pls check

Edited April 6, 2019 by FoxDelta

[BIGNEWY]

Excellent work!

[FoxDelta]

thx

[moespeeds]

Very nice work, and very generous of you to offer it to the community. Thank you!

[Shrike_AU]

Is there any chance you could put the fusion files up somewhere? I'm having trouble printing some parts and would like to tweak a few holes etc.

 

Great work BTW!

[FoxDelta]

PM d you