Aero4000 Posted Sunday at 04:58 PM Posted Sunday at 04:58 PM 6 часов назад, VR сказал: Or write a script, that moves PRMG beacon car to the opposite end if the landing heading changes. In reality, the beacon group does exactly the same. Though, it doesn't happen very often. According to my experience, there are usually 2 sets of PRMGs installed at an airfield. Only one of them is turned on, depending on the active runway. This is very similar to ILS. Спойлер 13700F, 64Gb DDR5 6000 MHz, RTX4080 16Gb, 27’ QHD 75 Гц FreeSync; Windows 11; VKB STECS Max HOTAS, VKB Gunfighter MK IV+ MCG Ultimate; VKB TRudder pedals MK V; VKB UCM Stronghold holders; Wireless TrackIR.
ED Team VR Posted Sunday at 06:41 PM ED Team Posted Sunday at 06:41 PM 1 час назад, Aero4000 сказал: According to my experience, there are usually 2 sets of PRMGs installed at an airfield. Only one of them is turned on, depending on the active runway. This is very similar to ILS. Yes, if stationary. If we'are speaking about mobile PRMG group it is not always the case. They might be assigned to specific airfield or even to a part of the highway when needed. And there might be a lack of them to have a runway covered from both sides at the same time. 3
NSAdonis85 Posted 15 hours ago Posted 15 hours ago On 9/21/2025 at 12:43 PM, VR said: Or write a script, that moves PRMG beacon car to the opposite end if the landing heading changes. In reality, the beacon group does exactly the same. Though, it doesn't happen very often. ...or, a thought: make a PRMG group that you can latch onto the runway instead of doing all the script and draw acrobatics to get them into the right places. Modules so far: FC3, Mirage 2000C, Mirage F1, MiG-15bis, MiG-19P, MiG-21Bis, MiG-29A, Mi-8, Ka-50 BS2/3, AH-64D, A-10C II, F-4E, F-14, F-15E, F-16C, F-86F, F/A-18C, Supercarrier, Syria, NTTR
Kuky Posted 7 hours ago Posted 7 hours ago (edited) I can't get this to work, I place the required units as specified, their location, heading, channel # etc, pick the same channel in cockpit but I still can't get landing bars to turn on... I don't know what I am doing wrong? MiG-29A Fulcrum Sukhum RSBN Landing.miz Edited 6 hours ago by Kuky PC specs: Windows 11 Home | Asus TUF Gaming B850-Plus WiFi | AMD Ryzen 7 9800X3D + LC 360 AIO | MSI RTX 5090 LC 360 AIO | 55" Samsung Odyssey Gen 2 | 64GB PC5-48000 DDR5 | 1TB M2 SSD for OS | 2TB M2 SSD for DCS | NZXT C1000 Gold ATX 3.1 1000W | TM Cougar Throttle, Floor Mounted MongoosT-50 Grip on TM Cougar board, MFG Crosswind, Track IR
ED Team VR Posted 7 minutes ago ED Team Posted 7 minutes ago 7 часов назад, Kuky сказал: I can't get this to work, I place the required units as specified, their location, heading, channel # etc, pick the same channel in cockpit but I still can't get landing bars to turn on... I don't know what I am doing wrong? MiG-29A Fulcrum Sukhum RSBN Landing.miz 8.55 \u043a\u0411 · 0 загрузок As I see in your mission the beacons are switched off. Activate the beacons as described in the opening post of this thread.
Recommended Posts