-
Posts
87 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Everything posted by huzar
-
PointCTRL - Finger Mounted VR Controller
huzar replied to MilesD's topic in PC Hardware and Related Software
You've got my full attention, Miles.- 3421 replies
-
- vr flight simulation
- vr gloves
-
(and 1 more)
Tagged with:
-
Completed throttle: I have added a number of switches to the base and encoder instead of mode switch. But biggest changes were done to the right throttle: - added analog thumb slew; - mouse nipple was replaced with 4-way hat switch; - top hat and slider were replaced with 2-way switches; - bottom potentiometer was replaced with encoder; - two 5-way hat switches on the front instead of single buttons; - additional single switch on the front of the throttle. Have been using it for over 2 months now and it's working great. My only gripe is with analog slew, it's not very precise and requires crazy amount of deadzone and curves in DCS settings. Also I'm not sure about current placement, maybe on the front would be better. And my current project::pilotfly:
-
I have just received mine and tested it on Virpil extension. It's a very tight fit but works, 10 seconds with dremel and brass brush resolved the issue.
-
Disable VR cursor-headset lock when Use Mouse enabled
huzar replied to Tailhook's topic in DCS Core Wish List
+1 -
VNAO DCS Ready Room VR Mod.
huzar replied to Particleman's topic in Utility/Program Mods for DCS World
Brilliant! -
No Mirage either. I get the 'beep' sound for new sources but no warning for locks or fired missiles.
-
And you can't buy 0.75 MDF in Europe... There is no easy way around the problem, someone will have to redraw the plans. Don't want to sound negative, I appreciate your work, especially as it's open source. If only it was that simple, you can't buy 19.05mm MDF so you will have to redesign all elements to accomodate for 18mm panels. 1mm doesn't sound much but it adds up with every element.
-
Ouch, engineering project in imperial system. That will stop anyone not in US from using your plans, as you can't simply recalculate dimmensions...
-
VZ_342, did you look at mmjoy2? Easier then hacking a real keyboard.
-
Thanks! Very helpful, waiting for more!
-
Can a latching toggle be made to be a single click?
huzar replied to truebrit's topic in PC Hardware and Related Software
You can do this using mmjoy2, it's possible to configure the toggle switch to simulate a single button press while switching to ON position and second button press while switching it OFF. Then in DCS settings setup first button for electrical power ON and second for OFF. -
Internals of the left throttle. It has mouse scroll with press button, paddle switch instead of original boat switch, left encoder has been replaced with potentiometer, additional front button and 2-way momentary switch on the left side. I didn't expect that wiring will take so much time. But I'm slowly getting there!
-
12 days to finish the throttle!
-
I also have this problem, no sound for lock / missile tracking just 'chirp' for new radiation sources. Makes SEAD missions very interesting:) Zeus, is there anything we can help with? Provide logs or something?
-
Cough... TOW... MILAN...:music_whistling: https://en.wikipedia.org/wiki/Wire-guided_missile
-
The Awesome Pedals - Hall Effect Rudder Pedals
huzar replied to AwesomestMaximusTheFifth's topic in Home Cockpits
This mechanism doesn't work very well, springs tension cancel each other out near the center and leave big dead zone, which going to be even worse with a dumper. -
[WIP] DIY Rudder pedals - design input wanted
huzar replied to FIN_Centurion1's topic in Home Cockpits
I have it done like that (magnet glued to the nut) and I haven't noticed any issues. I didn't test it in any scientific way, but as far as I can tell it works linearly throughout whole movement. -
[WIP] DIY Rudder pedals - design input wanted
huzar replied to FIN_Centurion1's topic in Home Cockpits
I have not yet seen a well designed, precise and good looking wooden pedals plus wood will wear and loose integrity rather quickly. It just not worth it when you spend so much time on designing, building, materials, tools etc. And my free time is the most valuable item in this equation. How did you design your cam profile? It was one thing I straggled with and at the end I opted for simpler centering mechanism. And I'm afraid your design for pedal brakes won't work very well, the upper rod will just twist under the load. I think the gas strut should be mounted directly to the pedal and then somehow fixed to the arm. -
It's what I'm doing as well and have modified my throttle to have mouse wheel that can be pressed for left click. Only to find out after trying F-5 that I need right button as well :joystick:
-
Thanks Sokol, in fact it was one of your post where I found about the MLX chip. A bit too late as the stick was almost done and I was in hurry to finish before Harrier release.
-
The ergonomics is my biggest complain as well, the stick was designed for vikings I think :lol: The hand rest is just a piece of foam cut to the shape of the stick fixed with double sided tape. The cutting is a bit crude but it's more comfortable then plastic. I can't remember where I got this foam from, IIRC it was packaging of some AV device, but it's very firm and doesn't give up much under the weight of a hand. Before I fixed the extension I had a twist mechanism in place as it helps keep the joystick together, just disconnected wires from the pot and used them for the lever.