71st_Mastiff

Is the laser supposed to show up on the mfd in the map tsd?

can you say; D-day! maybe the very reason they upgraded the Normandy map #2 ??!

Mmm I didn’t tk a friendly; I stupidly spawn in and someone was on the spot or flying into my spawn point and ended up crashing together, on the farp?

are blowing up as they leave the rails in Multiplayer after this last update.

The dots in VR now work!!

the flares are very stutters. not smooth when launched. it appears as if they are on a slide show.

Unfortunately; I had a feeling this would happen given the VEAO fiasco.

MT-BIN; Pimax VR. When the UI axis tune setting is open. Print screen only results in a black screen shot. I had to use My cell phone to get these screen shots.

I started using these settings, once you guys suggested its a problem with the axis, and low and behold; I can finally get a cross hair to lock on the Targets!! and the axis is smoother not stuttering, any longer. z-axis for the mouse stick on my throttle controller. Print-screens or any other screen shot with the UI opened in VR like this, would not take, I had to use my Cell phone to take the pictures of the UI axis tune setting. black out screen shots are from the print screen button while UI inside UI axis tune settings. The screen shots wouldn't work in MT-Bin VR. with the UI open inside the UI axis tune settings.

I pre-purchased the full map, does this mean I still get the high details? when the rest of the map comes along? or do I have to pay separate for the higher details on the 25% per-release maps being done?

ok got it working it was a firmware update I didn't know about for 4/2024

Is the flare animation ever going to be fixed?

you would think? since they are in a server and running down the road in a convoy , and spread out in a marshaling fielded position, they are still hot. and I can hear there engines running when I F7 to the vehicles.

So the AI still wall hacks; see through buildings and trees & brush and smoke, when is this going to be fixed? its ridicules' to approach a target stealthily and still get AI snipe because they see you coming through the smoke and trees and tall buildings.

sorry posted it in the wrong thread. I have a IRMV no thermal heat from soft targets, report going too.

Harrier IRMV, cant see trucks and soft targets. FLIR cant see soft targets gun trucks hmmvs. same no thermal on the AAA gun ZU trucks.

VR: Bin-MT: PiMax: Crystal: They will not lock a gun truck the trucks show up green as the screen and there not showing on flir; its like only see there shadow, and this is on Rotor Heads server. SP missions no issue. in SP same issue. DMT I see them no issues Same issue can't see them., IRMV nope blacked out cross hair wont lock it. Harrier AV8b. Thermal issues: aaa gun ZU truck there is no white hot or black hot detection on these trucks. track https://www.mediafire.com/file/jqmyflb0wq8gccs/SYRIA_TPE_v1_RUN1-20240315-131341.rar/file I see in the log desync issues.

DCS AV-8B N/A by RAZBAM Simulations Added: AGM-65E2. Updated: AGM-65 restrictions and limitations. Updated: MPCD brightness, video gain and contrast control. Note: MPCD brightness, gain, symbol and contrast key-binds must be done again. Updated: ROUTE Navigation. Updated: NASSAM SAM system added to RWR library. Improved: Sensor Select Switch (SSS) logic and key-binds. Note: SSS key-binds must be done again under special tabs for MFCD's the new control for setting the contrast brightness doesnt work.

doesnt work when the server goes desync!! which in my case because where I live; is all ways. cable; 500mbps down 20mbps up. ping to Los Angeles is 15 to 17 ms.

ok still issue even with out T-Pod, using DMT the cross hairs for IRMV Mavs still lock on ground textures instead of a target, sometimes locks take until .5 nm to lock a T-90.

The throttle collective has stopped working in the Helicopter, it works in the UI control panel, the inputs show its working. But when in the helicopter the throttle will not animation of it moving, I have to use my mouse wheel.

oh ok, I thought you where having a display issue with the coms menu show up in your right-side of monitor not canceling, Ill kindly back away into the brush..

did you cage the piper to the area of the target? You have to use TDC and move the piper to the target of interest then cage it, and then you should get the line; look on the left upper shroud, and see if you moved the knob from ccip- to ccrp?

no I use the default keys if you changed that, it wont work right.. default is "\" for simple and when you take of its "L-shft+\". Also if you have a monitor that's a TV; might be a scanning issue. you might have to deal with that in the Video graphics tools of your corresponding GPU brand you use? i.e. NVIDIA or AMD.

its not working on mine either. yep same thing, I had it self change to 72 hrz. When I run at 90.