The_Nephilim

Do you have Motion Blur enabled in DCS Settings? If it is not that do you have Vsync enabled?

well with the g2 limiting the fps in nvcp seems to have no effect?

So basically on the Quest 2 you set the HZ @ 90 then set the ASW at 30 well that is still ASW is it not?? it just limits the FPS too 30?? I Could try it too see for myself but I have a G2.. I can set the HZ to 90 but how will I lock the ASW too 30hz? I am sure this works but it still uses ASW..

I did not mean there was someting wrong with your PC just that your config could be wrong meaning your settings in Steam VR and DCS Perhaps. but if you are not happy with your 3090 you could send it too me and I would enjoy it for years to come haha!!

well I do believe there was a post a long time ago that discussed this issue.. There was a program to clear standby memory and they added it to the scheduled tasks, which helped alot of folks with this issue.. maybe do a search for clear standby memory?

Wonder why sounds like a bad config or something? I dont think ED is letting down the VR users sure it could run better but I have a lowly 1080GTX and looks good to me on low settings with a G2. EDIT: well I checked what it looked like in full rez on the G2 which is like 3xxx x 3xxxx but I have itlike 30% at 1784x1748 while not in its full glory it still is fun to fly in this sim.. I have put in a tree mod and the shader mod which helps performance a bit. I am hopefull with Vulkan in the near future I hope.

Ahh yes I keep forgetting to 2x the rez.. But I was just trying to do this more methodically then just guessing..

Well I had tried it at 32% and it seemed to look a bit better then the other way I was doing it.. I am just trying to figure out how many pixels a 1080GTX can push comfortably.. I seen someone mention the can game on a 3440x1440 monitor with a 1080 so I did the math and it is 4,953,600 pixels.. I am currently at 3,118,432. now I am sure it is a bit more complicated then that I am just trying to determine a round about number of pixels I should be able to push.. So far it has worked and I think I might be able to squeeze a bit more out of the old 1080gtx..

OK I just thought keeping the 1 at 50% and just lower the PD in DCS.. I will experiment with 32% and see.. I am doing the math and trying to keep it down the pixels I mean.

Yes I am well aware of this video but I am not trying to do this.. I just wanted to set the Res in Steam vr at 50% or my native res so I keep the 1:1Pixel ration then drop the PD too .8 I am not trying to do the .5 --500% trick..

I just checked the manual and it states it has a collimated lens.. I thought it was a fresnel lens I was wrong. so maybe this collimated lens has some funny issues I am seeing.. it is more in VR but I can look past it I was just trying to determine what the artifacts cause was, that is all and if anyone else is seeing it in VR..

Well I had messed with DCS for another few hours tweaking and here is what I came up with. 1. Resolution in Steam VR @ 2232x2184 which came out to be 50% I set it in per application, still 1:1 ratio and with DCS PD at .8.. here are my settings in DCS:

well my rig is not powerful enough to run the G2 at native res I run SteamVR @ 50%.. but I had a rift S and thought it could have been the rez of it but that is not it.. I think it is some wierd effect with the Fresnel lens on the EP-13..

Well if you are using VR there is a section in the Buttkicker that expalins how to get it working let me see if I can find that guide.. EDIT: Yes in the Buttkicker Gamer quick start guide page 3 is how to hook up the buttkicker with a USB headset which VR is..

Well while you may not be able to run the G2 at native res you can gedt by @50% res in steam vr even with all settings in DCS down to minimal it will look way better then the O+ I had a simialr run as you Odyssey +,, G2,, Rift S,, Back to a G2 and I have a 1080GTX..

Well I looked in to the Barell distortion thing and setting the correct native res. while you are correct about setting the rez higher in Link Settings it does not mean you can.. If you note in your Link settings pic where it states Render Resolution Resolution under the L there is a white tick mark that is the suggested setting for your System and is reccomended to use it.. I also note you said you tried it @1.0 and it did not effect anything well if that is true then there is something else that is wrong here.. maybe your PC is defective or OC too high or something.. but you said all your other games run fine but DCS being DCS is NOT the other games.. Not sure what to tell you but I would rety setting to the Reccomended tick mark there and restart the link Program and DCS and see what your Frametimes are? if your @1.7 but the settings program is reccomending lower higher is not gonna fix that Problem and yes I understand that is the native rez but like I said above just because it is the native rez does not mean you can run it at native res Are your setting in DCS the same and you are on a 3070? PErhpas try a Uninstall of GPU Drivers with DDU and reinstall newer drivers?

Well with the G2 I get the same effect in the EP-13 lens.. I am wondering if it is supposed to look like this or is it a weird lens issue with the EP13 Fresnel lens?

Hey Lucky, I just wanted to thank you again for a very seamless transition plus the fast ship time and getting it to the UPS for delivery to my house.. The Reverb G2 was in excellent condition and I had not had a problem with it. So hats off to Lucky for the great Price he offered the G2 at plus the shipping price ended up being a bit lower then he quoted and he refunded me the Difference A++.. If you happen to have a 3080 you wanna get rid of let me know..

Hey, I just bought a used Reverb G2 and I am going to see if I get the same effect on the EP-13 that I did with the Rift S. If it is still there in the G2 I will know it is something in the game which I think it is the Rift S lower res. or lenses or something. So we shall see.

Found a place to make them for me hopefully I can get a quick turnaround and good price

hmmm I do not think shapeways had that material listed?? thnx tho

Thank you for the help but I was looking for the breakdown of what PETG is Pertoleum electric tungsten gas?? I was going to get shapeways to print it up but I did not see any material that was PETG whatever it is?

Hey I just got a G2 and was looking to get these mods made up but I am trying to find out what is PETG? thnx

Your Welcome. Did you get it working now? if so great news good luck with it.

hmm well it seems you have to copy it, if it was tried on the Original Shortcut DCS put there when installing the game, the DCS_Updater.exe I dont think that will work is what I ment.. if it does my appologies..