admiki

Can you record another track that shows engine instruments? To me, it sounds like rotor was spooled down? Also, create your own mission and test this, training missions are behaving weird sometimes.

Did you forget to flip "take weapons control" switch back down?

Define combat load? I just got into hover at 5000 ft MSL/10°C FAT with 1880 lbs of fuel, 1 rocket pod/2 hellfires on each side. Are you trying to get into hover overweight for the conditions? Look, I am not saying that there are no problems with the way George is flying, I am just saying that there are ways to circumvent it. I did get into VRS if I comand him to stop into hover if he is climbing or descending to maintain radalt. I try to fly alongside mountain side when I want to get into hover. That way it is easier for George to maintain radalt and he manages to get into hover. Edited to add: look at your radalt before you give him comand to slow down. Give him higher radalt that currently is and he will climb into it while losing speed. That way he will not be too low on collective to let helicopter go into VRS.

I'm using Tacca's NVG mod.

You need to tell him where to look, what target to lock onto and (if not in free fire mode) give him permission to engage. Also, you need to make sure that you are positioned in such way that there would be no inhibit messages in HAD

Yes, he should be, yes, he isn't. It's WIP, it's a known problem. Interestingly enough, he is quite able to get me into hover without killing us, so maybe try to change how you do things until George gets fixed?

Same issue here.

They manage to hover after a while. Point is, to most of people that fly Apache or Hind (or any fixed wing) is more important to learn how to kill something than the nuances of flying the thing itself. Only after they are satisfied how good they are in shooting at something do they venture into learning the systems and how to fly it.

I know, but if rotor is turning right, your nose will turn left. Giving left pedal is not counteracting the torque, it is adding to torque

He did not mean it is low priority to you guys, he means to player base. And he does have a point. At Black Shark Den, maybe the largest pure RW DCS community, I have not met a new pilot that told me he does not know to shot HF. Yet 80/85% could not hold a hover worth of ****.

TBH, I never tested it, but I think it would be set by George, unless you jump to the front before startup is completed.

You got this backwards

You mean to safe the aircraft? Post a track

Do you have pedals? Honestly, you need to figure out what is important for you and how you use your controls. I have one, but it might not work for you due to aforementioned conditions

Yes I did. Look what I circled in red. Your current rad alt is 400, your comanded rad alt is 270. When you initiated slow down, you were at about 370 ft AGL. You comanded him to slow down into hover and to descend. Don't do that. Edited to add: you might not have comanded descent, you might be over hilly terrain. Nevertheless, it is up to you to pay attention to your suroundings and act accordingly. Yes, George sucks. It's WIP. That's why I get into hover myself or close to it and only then give control to George. You want fire-and-forget George? It's still WIP.

What did I just say? Dont get him slowing into hover and descending? Either get him to get into hover and descend or descend and get him into hover. Not both at the same time

IME, George will VRS if asked to get into hover while doing something else like turning, descending....... Just slowing into hover works fine. Then you can descend or turn.

Check general and UI layers

And then you don't know when your load is swinging?

Where did you find this? Mi-24/35 is pure LOS guidance

Weapons action switch on cyclic

I would love to have SPO-15, "but it's not realistic!" gang be damned

Not what you are looking for, but think about what YOU need and will work for YOU.

Yeah, I agree. But it is playable at 1920x1080, so at least you got that

OK, one last idea. Drop resolution to something low, 1080p or less and try again